Tranny Hump Removal

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 14, 2019
Threads
3
Messages
7
Location
Central Coast Cali
Gents,

I think I watched a movie named "Tranny Hump Removal" once. But I digress...

First post, and sure not to be the last, as I recently reduced to possession a 74 FJ Cruiser that needs a little attention. And I'm a total Noob when it comes to FJ's and restoring them.

Until such a time that I can do a full resto, I'm doing some stop-gap stuff...rust removal, priming, etc. The underside of my tranny hump...or what's left of it...where it bolts to the tub, is looking pretty ratty. The gasket that is supposed to be there is pretty much gone. I'd like to clean it up and replace the gasket, but I'm not sure of the best/accepted way to take the hump out. It looks like it could come out a couple of ways. The seats, gas tank, etc. are already out, by the way.

What say you? Advice is appreciated.

Justin
 
First advice is to not call it a FJ Cruiser. Acceptable names include FJ, cruiser, Landcruiser, FJ40, 40.

Anyway, enough busting your balls. I'm not the expert here as much as others are, but I don't really remember there being a gasket between. Maybe some tar paper or something but I haven't pulled one off in a while.
 
Welcome, and congrats. I also am the proud owner of a 1974 FJ40.

The underside of our tranny hump was pretty nasty. I have a thread going on the refresh of our 40. Look at post #70, it will show you how we got ours cleaned up. Link.

There are tranny hump gaskets available, I am pretty sure we got ours from SOR.

Enjoy it, I would not trade ours for any other. Working on them will get you attached, at least it did us.
 
MadMace,

Thank you for the reply and the link. I found ALL kinds of interesting info in your thread. And nice work on your FJ40.

Looking at your pictures answered my question...I think. It looks like you pulled your heater out so as to physically remove your hump. The other option appears to be removing the gear shift somehow so you can pull the hump.

Justin
 
Heater removal is not neccassary. Removing the shifters is the way to go. The transfer ones are pretty easy, the transmission can be difficult depending on the spring You need to push down on the retainer at the base of the shifter and turn CCW, 1/4-1/2 turn and it will pop out. Make sure it is in neutral first to make installation easier.
 
As Travis 76 said, no need to remove the heater. I had removed the heater to give it a good cleaning. I did not have to remove my shifter to get the tranny hump off but I did have to change the angle of the hump several times as I was lifting it off to get it over the shifter. Would have been easier in retrospect to have removed the shifter. lIke Travis 76 said, if you do remove the shifter, make sure it is in neutral when you do.

Having the Factory service manuals will be important for you to have. They are full of invaluable information. Fortunately you can download them due to the work of Trollhole to make them available. You need the engine FSM and the 1971 Chassis and Body Manual. Download and print these, you will be using them ALOT.
 
First advice is to not call it a FJ Cruiser. Acceptable names include cruiser, Landcruiser, FJ40, 40.

Fixed it for you Airon23 :)

I do not know if your interpretation of rust is the same as mine (your in CA and me in NY)... however... when removing the bolts be prepared for several to snap off if you have 'rust'... you can douse with PBBlaster from under .... but... those like to snap regardless
 
JohnnyC,

LMAO! I've snapped five so far! For a couple of weeks, every time I walked by my FJ, I doused the broken studs with Kroil in preparation for the extraction process. I went after them a couple of days ago. First one came out in a minute or two. The next three...not so much. I got them out eventually, but it involved a lot of foul language and broken screw extractors. The fifth one, which is conveniently located right below the heater, awaits my attention. Good times!

Justin
 
Fixed it for you Airon23 :)

I do not know if your interpretation of rust is the same as mine (your in CA and me in NY)... however... when removing the bolts be prepared for several to snap off if you have 'rust'... you can douse with PBBlaster from under .... but... those like to snap regardless


What I have done in the past is run nuts on the exposed thread of the bolts. Soak it with something for the rust. Then while unbolting when it binds tighten then loosen again. Rinsing crap off the threads on the bottom during process helps. Not sure on a 74 but know my 68 and earlier cruisers have a square nut in a cage. I use a visegrip to hold the nut tight in the cage to prevent it from spinning.
 
Back
Top Bottom