Trail removed my flares - help, hints needed.......

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 10, 2008
Threads
33
Messages
502
Location
South Wales, UK
Hi guys,

Been off roading around West and Mid Wales all weekend. One trail got really tight and a tree tore off all my front PS flare and half the rear.

Getting tight in there..........

100_0161.jpg


Yup, they've gone..........

100_0162.jpg



So, I've now completely removed all flares from both sides of the truck. No panel damage but I've got lots and lots of holes left showing.

My question is - what have you guys been doing to fill or cover these holes after you've de-flared your truck.

Thanks

ps - the bonnet is up because that trail also stopped the engine (almost). A single large leaf had been sucked over my snorkel intake allowing it to idle and nothing else - so Cruisers can be stopped!
 
My question is - what have you guys been doing to fill or cover these holes after you've de-flared your truck.

I've seen guys put in plastic caps just to cover the holes and then rhino line/line-x the flares.

ps - the bonnet is up because that trail also stopped the engine (almost). A single large leaf had been sucked over my snorkel intake allowing it to idle and nothing else - so Cruisers can be stopped!

Thats a first. A freaking leaf is enough to take down the mighty beast :doh:

Perhaps this is another indication that you need to have the intake for the snorkel facing backwards.
 
BTW I was at a car show yesterday in Lancaster and there was a lifted 80 with a snorkel and it was facing backwards. Two guys in a Land Rover parked right in front of it were trying to make fun of the no-where-to-be-seen 80 owner about the snorkel intake being installed wrong. I didn't say a word. :D
 
"Backwards" is a subjective term. I've seen several professional rigs position the intake facing the rear, meaning air is not rammed down the intake at speed. I don't know the arguments for choosing which direction in a given situation, but it was probably positioned that way on purpose. Which purpose is the question.

Perhaps so a leaf can't stick to the opening....
 
BOYO's new avatar

That is hilarious - I'll get it up ASAP.

Hadn't thought about turning it around - and that would have done the trick. Would have taken me about 1 minute to do!
 
i'm in the process as well of filling those holes. I am thinking of aluminum tape in small pieces, just to cover the holes and UPOL over them, I am going to try to MIG up some of the holes with a wet rag on the constant to keep the sheet metal cool & not warp... I like the plasic plugs under the UPOL... any more wisdom? NICE AVATAR!
 
Congrats, With all the threads of how to remove your flares, yours seems like the simplest and least amount of work :hillbilly:
 
Congrats, With all the threads of how to remove your flares, yours seems like the simplest and least amount of work :hillbilly:

It took all of a few of seconds - CRUNCH, CRUNCH - job done!

Took me about an hour or so to take the rest of it off today.

Can't get used to the skinny look the truck has though....
 
Your question is very timely. My flares came off about 10 minutes ago. Back to the au natural look and I like it. In my search on the subject someone mentioned using jbweld stick to fill the holes. I have never used the stuff so can't provide input as to effectiveness.

Has anyone been sucsesfull with the jb stuff? BTW I am going to coat with Duplicolor for a smoother finished look.
 
no JB Weld ever?!? lol, love the stuff :), just be sure to clean and scuff the surface good to get a good bond. I swear half my of my Ghia was made of it. ;)
 
First, good move. Your girl now has much sexier lines without those big plastic hips :D.

Second, mine are just plugged with some plastic plugs from Home Depot (stateside of course). But my rig was white, so white plugs worked perfectly. Then I Durabak'd it and it's all just covered up now.

I'd use Fast Steel (or equivalent) as recommended above, and then a bedliner for those tight trails. Never have to think about it again.
 
First, good move. Your girl now has much sexier lines without those big plastic hips :D.

Second, mine are just plugged with some plastic plugs from Home Depot (stateside of course). But my rig was white, so white plugs worked perfectly. Then I Durabak'd it and it's all just covered up now.

I'd use Fast Steel (or equivalent) as recommended above, and then a bedliner for those tight trails. Never have to think about it again.


I swear that it cut through the air cleaner when I was driving last night lol.

OK - Thanks for all the tips - I'll try the plastic metal - I've had good results with that in the past.

Although I do like the plastic plug idea - dig 'em back out if I want to pick up the holes for something at a later date.....
 
"Backwards" is a subjective term. I've seen several professional rigs position the intake facing the rear, meaning air is not rammed down the intake at speed. I don't know the arguments for choosing which direction in a given situation, but it was probably positioned that way on purpose. Which purpose is the question.

Perhaps so a leaf can't stick to the opening....

That and our engines are very large air pumps anyway so it doesn't matter where the air comes from.

Its not prejudice if it comes from the front or the rear...:D HE HE

Now back to the flares, good luck and I would go with plugs so you can add them back at a later date, or when it comes time to sell etc...
 
Hey........

hehe how are you..... Hope u are well mate....
Love the Avatar....

I read all about it on the Hilux forum....
Shame you have gone the skinny look, I am not a big fan of it.. why not get some Rubber flares...??

I guess that lane is safe for me to drive then now ay.....
 
That and our engines are very large air pumps anyway so it doesn't matter where the air comes from.

Its not prejudice if it comes from the front or the rear...:D HE HE

Now back to the flares, good luck and I would go with plugs so you can add them back at a later date, or when it comes time to sell etc...

Ram air effectivity is highly overrated. Even in high reving hondas, there is not much "dyno proof". And most trail riding is at low speeds.

Not to mention that snorkels usually hurt performance.
 
Back
Top Bottom