threading the antenna replacement wiring?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 9, 2017
Threads
366
Messages
2,589
Location
tejas
gents
i removed the power antenna and motor but in getting it out the wire back to the stereo seems to have dropped down into that well. i can’t figure out if it is hanging down inside or what because it doesn’t seem to be laying down at the bottom.
is it possible to remove something to get in there? i can’t figure this out.
if i can’t it /seems/ like my only option is to pull it from inside the glove box. even though i would really prefer taking a stab at tying the new one to the old one and taping it up real well and pulling it though. that said, that mother is TIGHT as s*** in there.
anyway, if i can’t get to it and just need to yank it - can i thread the new one through the hole for the door wiring without ruining my waterproofing in this area? i really don’t want to do this obviously.
or can i run it through the firewall though one of these grommets?
thanks for any help!

23DFCDE0-C8C0-441E-9F11-792D2E72E8F9.webp


BEE2BB9C-2471-4825-83A4-00C896298576.webp


5D65D7A0-9283-4FFD-9D9A-20BAB7239487.webp


50AFF882-BADA-4E9D-819A-F5CDB135060E.webp
 
On the inside of the fender in the engine bay there is hole you can reach down and feed the antenna wire through. I had better luck feeding mine from the outside into the cab.
 
Under the fender there is a rubber grommet in the sheet metal that the antenna wire feeds to.

I removed fender & grommet $ the wire was still stuck behind the rats nest of wiring & vent ducts.

I pulled & eventually tore the wire in two.

I wasn’t about to pull my entire dash & begin pulling wire looms & vent ducting.

I even removed my passenger airbag, I still couldn’t get in here.

My story doesn’t help you any, but just explains how impossible it seems to get to.
YMMV.
 
hi gents. thanks a lot. not so easy to explain this one.

so i /can/ see in to the "wheel well" if i get my head inside the PS wheel and look in. but i can't see the old antenna cable. i fished around with a coat hangar for awhile and i still can't feel it. i started to think it may be /hanging/ from where it exits the passenger compartment. the deal is it seems to travel /behind/ the firewall and then scoots over to connect up where the antenna was. but when it got cut it seems to have fallen in.

before it got cut i could tell it would take a /lot/ of force to get it to move. i mean, i was able to free it up all the way to the right side of the glove box and get my hand up in there and see it wasn't clipped into anything. BUT if i pulled from the inside or if i pulled on the antenna from the outside from within the wheel well i could tell it wasn't going to move unless i really pulled it extremely hard.

so i am not convinced that even if i was able to find it i could get the new one through. and the problem is that now since i have only access to the end on the inside i would have to pull it through and not be able to "fish"anything after it. i mean ideally i would be able to tie some twine with a wire core on the inside and yank it through and attach the new antenna. or alternatively attach the antenna from the outside to it and pull it back through. but again it is MIGHTY tight.

you can see the red arrows where i can see into the wheel well. but is there a way to open this area up some more?

alternatively, i CAN get the NEW cable through the wheel well and scoot it up to the inside of the door with no chance of it binding. so if i can send it through the rubber grommet with the door cabling it would work really nicely. but i don't want to start screwing with this water tight grommet with tape on it if i could create a leak.

alternatively someone said they sent it through the firewall. but this also involves monkeying with rubber water tight seals. two of these are in the first images.

i'd welcome help. i think it is a bad idea for me to drive it with the radio and the trim panels all hanging out.

THANKS for any ideas.

Screen Shot 2019-02-24 at 11.04.03 PM.webp


Screen Shot 2019-02-24 at 11.03.52 PM.webp


Screen Shot 2019-02-24 at 11.02.48 PM.webp


IMG_CC2F33ED7825-1.webp
 
Under the fender there is a rubber grommet in the sheet metal that the antenna wire feeds to.

I removed fender & grommet $ the wire was still stuck behind the rats nest of wiring & vent ducts.

I pulled & eventually tore the wire in two.

I wasn’t about to pull my entire dash & begin pulling wire looms & vent ducting.

I even removed my passenger airbag, I still couldn’t get in here.

My story doesn’t help you any, but just explains how impossible it seems to get to.
YMMV.

jesus. ok. so where is this rubber grommet exactly? and how do i get to it?

i have to admit i still can't understand what folks are talking about when they talk about removing the "skirt" or the wheel well or even the fender. i mean, can i get down into that hole where the antenna motor sits so i can get a hand in there?

i /can/ see i have some daylight in there if i stick my head up behind the wheel and look back but i can just get a coat hanger in there. and i can see that i have a vertical slit into there from the passenger side door. i mean, i can feed the freaking new antenna through this slot but i have to get it up into the interior.

and i /could/ shove it through the nicely sealed hole for the passenger side door electrics. but i tried this and i think i am going to have to really work on it to get it though here. there's not much room to work. plus i DON't want to screw up this watertight seal.

anyway, what did you end up doing if the original got shredded? i mean you still need to get the new one inside don't you?

now that i am thinking about this it would have been a hell of a lot easier to cut and splice it at the antenna. well, not a hell of a lot easier but at this point i am starting to wonder...
 
On the inside of the fender in the engine bay there is hole you can reach down and feed the antenna wire through. I had better luck feeding mine from the outside into the cab.

hey man. are you talking one of these two? and if so, you are showing the new cable through one of them (somehow?) and then fishing it up behind the glove box and grabbing it from inside?

i don’t know if the LX has extra stereo wiring in here or some additional electronics but i am pretty sure the existing one is going to shred when i pull it through from the glovebox side.

also. what do you think of the hole at the DOOR? this is a mighty attractive place to feed the new antenna through. but i’m worries about screwing up a water tight assembly...

324A0FD5-E557-421A-A54D-642F8E33BA92.webp


889A6E98-C1F9-459E-929D-47BCBCDC19EA.webp
 
I spliced my new cable onto the old cable. Its kind of tough to do. You have to provide a splint to support the splice of it may break. If I were to run the cable all together, I would probably remove the passenger door. Then you could probably reach into the hole for the antenna easier. It's actually not to hard to pull the door off. Need some ratchet wrenches though.
 
I spliced my new cable onto the old cable. Its kind of tough to do. You have to provide a splint to support the splice of it may break. If I were to run the cable all together, I would probably remove the passenger door. Then you could probably reach into the hole for the antenna easier. It's actually not to hard to pull the door off. Need some ratchet wrenches though.

can i pull a fender or something? or some kind of panel somehwere or something?

i was thinking to pull the door to feed it through the HOLE for the door wiring.

but i can only see a very thin vertical opening into the wheel well with the door on or off. i don’t think removing the door will give me /access/ to the wheel well.

and i pulled the trim piece to see if i could reach up but it is closed.

ALSO, how do you pull the door? you have to remove the panel and disconnect all the wiring i guess?

edit: this pic is the part that you can get at after removing that integral mudflap. but if you take rhisnoff the wheel well is still closed under this part...

1913332
 
this is the gap from the passenger side of the door that is “directly connected” to the wheel well...

well. it’s not really a wheel well IMHO. it is more like a hidden compartment above and behind the wheel well...

1913333
 
When I looked at mine I felt fairly confident I could get to the hole of I removed the door. To remove the door roll the window down, u have to pop off the kick panel in the foot well, then unplug the door plug wires and feed them through the body hole so they just hang in the jam. Then pull the door check stop pin, then remove the hinge bolts until you have one bolt holding each hinge. Put masking tape on the door and fender near the jam so u don't scratch the paint. Have someone hold the door by the window frame-why u rolled down the window. Then take off last 2 bolts. Takes about 30 minutes I'm guessing.
 
Their is also a hole by the cruise control in the engine compartment that gives access to the inner fender but u need long arms. I could just barely reach the antenna hole this way.

hmmm. can you help me find this? also, how do you access it exactly?

i am having a hard time figuring out what this inner fender space looks like.

i mean, right now the speaker wire goes from the back of the glovebox through sheet metal, into this void space, then attaches to the antenna?

so how do i get it through the hole in the cruise control and then back out through to the antenna - assuming i could reach it...?

1913435


4F6AB4B9-A42B-4028-9E26-66795A984B5F.webp
 
The hole is by the cruise control actuator mounted on the passenger fenderwell behind the air filter. It's not on the firewall. It's on the side of the engine compartment.

thanks. sorry, this turned into an episode of mcgyver over here.

seems to me there is the void where the antenna gets mounted. you put it through the hole and mount it in this void. then the original antenna disappeared down into this void and - i guess - jumps through the frame at the glove box and gets into this void somehow?

i have the antenna mounted inside this void and the wire is in this void so i am trying to figure out how to get to the back of the glovebox.

is the hole front to back through the firewall? or i guess you are saying it is inside the void and will get me through to the back of the glovebox?

i think it is going from the engine bay into this void i guess...?

A0853709-8F28-4D55-8F0E-17890E1F114D.webp
 
Pulling the fender will give you unobstructed access to the rubber grommet the antenna wire feeds to.
Fender is easy to remove.
Pull corner light to reveal screw, the top of the fender, right along the hood line-all those screws. Screws under the vent cowering near windshield. 2 screws/bolts at the very bottom of the fender, right next to door...
 
Back
Top Bottom