The James Caird

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 8, 2006
Threads
266
Messages
9,823
Location
Ashland, OR
Website
www.jeffersonstatecruisers.com
Well I found the problem...... Timing chain broke.... I never would have thought.... Never made a bad noise.... nothing! The chain was hanging on the cam sprocket perfectly centered, so the ends were just touching the crank sprocket.... And the drivers side metal chain guide lost it's top, which must have jammed the chain and snapped it.... Very strange.... Fingers crossed that I didn't bend any valves.

I ran out of light tonight, but tomorrow I should know more.... (If I feel like doing anything after work.... :p)

Thanks for all of your help on this guys and gals! :cheers: I don't know if I'll be up and running by the 12th... good think Garett offered me his 80 to take out while he's gone! Hehehe
0629082125.webp
 
WOW! How did you determine it was the chain? That's pretty far from an electrical problem.

The 80 you say, well it looks like I won't have the flares replaced by then and that is throwing off the weight distribution, I wouldn't let someone take the rig it it's unsafe condition ;)
 
I wouldn't let someone take the rig it it's unsafe condition ;)

Right you are! :D I hadn't thought of the weight problem.....

I arrived at my diagnosis after everything tested fine, all the electric stuff is good, test good, nothings wrong...... So what the _______!!!! As I had test wires strung across the engine, and light bulbs.... and the timing gun..... I thought "If the dist isn't turning.... then I'd have no spark..." I pulled the cap off, cranked it over... and it didn't move. Bingo!

So now I either have a weekend of work.... or a month of engine building.... Or I start looking for an engine.... or parts truck.... We'll see. I'm relieved that I know the problem, but a little miffed that it was that bad! Hehehe :eek::eek::eek:
 
Nice deduction. At what point will you know if there was more damage than just the chain? Do you put on a new one and fire it up or will it be a disassembly and inspection? Is the possible damage caused by your crank still turning while the cam stopped? If so, is that the concern with the valves? Seems as if the cam stopped there wouldn't be any detonation in the cylinders just compression.
 
The way the cam stopped, I think 2 cylinders were closed up, but without spark nothing would happen there. Yes, the 22RE is an interference engine, so I could have bent valves, but I never heard anything to make me think that.... I'll check to see if the valve clearance is back to spec when they are fully closed, that will tell me if I bent any.
 
In older motors if a timing chain broke the inertia would keep motor turning over, however, withouth the cam turning the open valves would stay open and the closed closed so the pistons would run up and smash the valves to smitherienes. In more modern motors if the chain, or belt breaks then the valves all stick closed and avoid damage, and/or the pistons are clearanced so that if they are open they will not hit....
 
Ouch! x2.:crybaby:

Bummer. That was the last thing I would have suspected. Keep us posted on the valves.
 
All but one of the valve lash settings were right on... The #3 exhaust is supposed to be at .30 mm , but it's up at .45 mm.... That could indicate a bent valve... I checked the cycling of the valves, and that one could have been hit all on it's own at one point in the cam shaft rotation.... I've been pulling it apart, and am almost down to the timing cover and pan.... There's a lot of junk in the way.... It's not looking toooo bad yet. :D Should have it up and running by winter..... :p
 
All but one of the valve lash settings were right on... The #3 exhaust is supposed to be at .30 mm , but it's up at .45 mm.... That could indicate a bent valve... I checked the cycling of the valves, and that one could have been hit all on it's own at one point in the cam shaft rotation.... I've been pulling it apart, and am almost down to the timing cover and pan.... There's a lot of junk in the way.... It's not looking toooo bad yet. :D Should have it up and running by winter..... :p
No you have to get it running before that. I only have 2 wheel drive right now so I can't tow you EVERYWHERE ; p
 
New chain is in, compression was 157-185ish. So it's going back together! :cheers:

No problems with the #3 exhaust valve?

What's the range on the spec for the exhaust valves? What else could cause that valve to be so far out of spec?
 
I have put the last 3 days in working on the 40, swapping steering boxes and cleaning up the front end. I don't like wrenching in the dirt and heat but it's stuff I can't tackle at my house.
 
Where have you been wrenching in the dirt?
 
Ok, so I fixed the AFM plug that left me dead at the store last weekend... It just fell out... The truck didn't want to run too well with that unplugged...

And today I had a chance to try and fix the coolant leak... It's drying now, so tomorrow I'll fill 'er back up, and give it a test run. If it's good I'll be cruising on McGrew in style, if something else goes wrong..... I'll be waiting in style on McGrew..... :D Wish me luck!
 
...if something else goes wrong..... I'll be waiting in style on McGrew..... :D Wish me luck!

That was a little prophetic...

So! Good news, Engnbldr is going to warranty the timing set. The bad news, it's not leaking oil from quite where I thought it was... Turns out the new bolt I got to hopefully stop the oil weeping like it did last time I had the cover off, was too long... and it broke my timing cover... that's where it is leaking... :sigh:

So, anyone have any 22RE parts around? I need a valve or 2, and a new timing cover. Preferable cheap, because I'm out of fun money for a while.
 
Back
Top Bottom