Temp RR 1/4 rust patch

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 12, 2008
Threads
300
Messages
3,609
Location
West MI near GVSU
Website
www.mcdesignsoffroad.com
So after redneck patching two holes in the floor of our truck, I was at a loss of how to close up the major hole behind the RR tire.

While sifting through my possible junk metal sources I recalled that I had a mostly intact chunk on a somewhat cut up carcass laying upside down in my old polebarn.

A few cutoff wheels, one sawzall demo blade and a few gashes to the back of my hand and I have a factory patch. I’m not going to make it pretty, just sealed. No welding, just screws and sealer goo.

I’m replacing this rusty hulk with a whole new rust free body and frame next year. I’ll just swap everything over after it’s painted.

The patch is upside down, but I think it’s obvious how this will go.

Maybe I should give up?


30580D9D-DCE2-4ED4-A1B0-08D94D5B2680.webp


B1542C79-18A1-4960-8A25-60902D36CF8D.webp


EF74376C-1A05-4167-A3B6-9AC5AC0D6121.webp
 
Last edited:
So I spent some time with my angle grinder today to get the patch to fit. I have a bit of rust to clean and patch up, but it will go on nicely and stay hidden by a “new” bumper cover end.

I can’t wait to start work on the new rust free body and frame!

B75BBD4D-F79A-40BE-9025-867CE1C2F739.webp


0EBFCE5F-FD07-4EB2-A197-2E9F0673A4AA.webp


86A6DDE5-DB23-4F0D-8315-AE642E395522.webp


351BCCD9-C63F-4C6D-80F7-5213246200B3.webp
 
That looks great. I was doing that with the resonator attached. Don't forget the rust inhibitor.
 
Could leave it off flat patch it , then do high clearance bumper

That’s my plan with the new body. This is a temporary red necked patch to get the current rusty beast sealed up and running.

My plan is to get the new body totally modded and prepped before a full new paint job. Once that’s done I’ll swap everything usable over.

I’m going to go for a darker version of the dusty blue on lots of the current Tacos and 4Runners. No more metallic.

The new frame is totally rust free, but has some booger cutting at the back that I can address, then do a low lift front 3-link, maybe a proper rear triangulated 4-link and then have it powder coated.

The rear bumper will be ‘Labs inspired, but the wings will tuck up high under the rear 1/4 cut.
 
Last edited:
So, with another grill tank filled so I can fight more rust I continue...

The bottom patch is nearly ready to go on. In the mean time I pulled the tail gate to get access to the bottom corner and to finish pulling the stupid plastic bumper cover end. Only one bolt came out. The rest either broke or had to be cut off.

I can’t wait to get a clean truck!

I also played with a couple of mud tires too. 33” LTB and 35” old bfg from my 40.

50891A9B-40B2-4BFF-91E4-E500DD7D4673.webp


6092689B-5942-4CAE-BB80-3F95007F2A8B.webp


E4E3ABCA-0206-44B8-929A-7A47C26E04B7.webp


44522B97-04A3-4895-8ED8-EC7E434624F6.webp


CAC4D7BE-7313-4A55-9BFE-83DA948AEB98.webp
 
The patch is on, sealed up and painted. I still have some more paint to shoot on the fender flare hole patches when I get a day that isn’t too cold or windy for my little turbo heater to keep up.

...AND, I got a buddy to help me pick up the rust free 95 carcass from another local cruiser buddy.

862E1557-DFB2-48F7-8979-6564C93D0885.webp


DF8F36AF-4E64-4870-ADAA-57E0437F8CA8.webp


3DFB5D26-4000-4FE0-A992-FF1C6984FB55.webp


CE4BA443-5DC3-4899-93E2-11F36DDF1B5C.webp


A77952CD-E920-4289-8690-6BD6DE8D69E6.webp
 
Back
Top Bottom