Swapping in Lockers

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 29, 2011
Threads
75
Messages
3,551
Location
Phoenix, AZ
I recently bought an LX450 with lockers with the intention of swapping the axles and other bits over to my unlocked 1995 80 series. Any experience/opinions regarding swapping the entire axles vs the third members and the required drilling and notching? The lx has about 100k miles less than my 80, but my 80 has had the front axles serviced in the last 5000 miles, lx probably never. Drove the LX 3 hours home with no issues.
 
I prefer swapping the whole axles.



So why part the LX?

Hey Kevin,
The Lx has a restored salvage title and is covered in bed liner. It won’t be parted out, I am going to take the axles, 4x4 labs rear bumper, Slee front bumper and put those on my 80. My 80 parts would go back to the Lx. I may keep the lx450 around or sell it. It runs and drives great. The interior is also pretty clean, seats were redone tastefully with leather.
 
I swapped out entire axles on mine. Was definitely some work. I did because i purchased a new 80 that was bone stock and wanted my locked axles plus all the maintenance i had done on my current axles. Good time to do bushing as well.

20161031_141943.webp
 
I swapped the front 3rd to an unlocked housing, and would also recommend swapping the complete axles. It's very difficult to get the front 3rd to seal properly, and it's tough to get the studs drilled and tapped just right. Besides, what are you going to do with the unlocked 3rd? You'd have to retrofit the locked housing as well, or sell the parts separately. There's a good market for unlocked 80 axles
 
You can't put the factory bumper back on after you take the 4x4 labs bumper off, FYI.

I will be cutting one off of my 80, so simply welding that back on to the 450.
 
I swapped the front 3rd to an unlocked housing, and would also recommend swapping the complete axles. It's very difficult to get the front 3rd to seal properly, and it's tough to get the studs drilled and tapped just right. Besides, what are you going to do with the unlocked 3rd? You'd have to retrofit the locked housing as well, or sell the parts separately. There's a good market for unlocked 80 axles

Good point on putting the unlocked 3rds back into the locked housings. So that solves that question. I figured someone would add something I hadn't thought out yet.:clap:
 
When I did mine, I looked at the complexity of the rear housing (i.e. how many different nuts and bolts have to be undone) vs just swapping 3rd members, and opted to just swap 3rds. There are no holes to drill, Just have to swap studs for longer ones. Use a grinder and burr bit to notch your housing, and you are done there. Then swap the RH axle shaft for the longer one out of the locked housing. I would do it that way again if I had the option. The front axle I swapped the whole thing. For the same reason. In my opinion, it's less (tedious) work overall. Plus I didn't have a jig or a trustworthy drill to perform the procedures on the front housing. It was less screw-up-able. haha.
 
Honestly, if I came across locked axles I would swap straight across. Yes, I understand your axles have been refreshed, but with the time you are going to save by swapping in the whole axle versus notching your existing 3rd member housings, and the other work that needs to be done you could put that time saved by swapping axles into refreshing the locked axles.

Make sense?
 
Honestly, if I came across locked axles I would swap straight across. Yes, I understand your axles have been refreshed, but with the time you are going to save by swapping in the whole axle versus notching your existing 3rd member housings, and the other work that needs to be done you could put that time saved by swapping axles into refreshing the locked axles.

Make sense?

I did my front and rear locker retrofit in a single weekend. It's not that hard, or complicated, just takes time, especially if you laying on your back under the truck.
Stripping and re-assembling knuckles at the same time makes it a big task.

Swapping complete axles, stripping brakes, cables etc, redoing bushes is still going to be a fairly solid day, or maybe two day mission for most.
 
Back
Top Bottom