Supercharger not creating any boost

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 15, 2006
Threads
80
Messages
2,843
Location
Lincoln, NE
1996 FZJ80. Supercharger installed 5 weeks ago and -was- working fine.

Two weeks ago my wife borrowed my truck for a week while I was waiting for a new starter motor for her's from cruiserdan. (I know... but she can't drive my other car since it's a stick.)

Last weekend my truck had no power left at 60mph and got about 7mpg.

SC nose and belt are turning.

Vacuum measured at intake port (per SC instructions) is now reading 20inHg vacuum at idle and pegs the gauge in vacuum at throttle.

I.e. this solves the age old question of whether the truck will still run with the SC failing. It does, but don't count on being in a hurry or passing anything

Kind of clear to me that the Supercharger isn't doing it's job. So... before I tear it all apart again, does anyone have any idea of what I'm looking for?

Thanks.
 
Is there a good way to check that without disassembling the thing? Not happening until after thanksgiving weekend if I have to tear it apart.:frown:
 
Sorry to hear about this Grench, first the EGR meltdown now this....

You should be able to push the bypass open manually to see if it is opening and closing without taking anything apart.

https://forum.ih8mud.com/80-series-tech/252022-sumotoy-zero-boost-sc-mod.html

How are the small hose clamps positioned? I know that if they can be in a position that interferes with the S/C operation.

For reference, mine usually reads about 20mmHg at idle, then drops during acceleration and eventually up to 6-7 PSI under full acceleration/boost. If I am at highway speeds and suddenly let off the skinny pedal, I can see the vac go as high as 25 to maybe 30 mmHg.

Just curious, what kind/brand of gauge are you using to read pressure/vac?

Maybe you could also go through and make sure all the 3" hoses and connections are still tight.

I know this is a far out possibility, but how is your oil pressure and power steering? There isn't a chance that the crank bolt has come loose is there? I'd imagine you would be having more noticeable problems right mow if it had come loose.

I'd hold off on tearing it apart just yet, but it might be a good idea not to drive it very much until the problem is discovered.

I wish I was closer to help you troubleshoot. Let me know if you need any pics etc.

Edit: EBag beat me to it.
 
Last edited:
See pictures on this site.
Kazuma Supercharger Install

When I did mine (one of the first installed outside TRD) the hose clamp caught the bypass valve and it stuck open. This happened on the first drive. I did not have a boos gauge at the time, so I did not know it was not boosting. All that I thought was wow, that $3k piece of sh%(&t does not make much power. :D Once I found out what was going on, the bypass actuator was broken. TRD replaced it free of charge. So I guess I proved the Sumotoy bypass test about 9 years go :D

My experience prompted George to add the comments to his site. This was all pre MUD. Amazing what we did before MUD existed :D
 
The bypass valve moves freely through it's range. When returning from the open to closed positions (engine off pushing it with a finger) it makes an audible pop like the sound fx in the lollipop song. Normal?

The hose clamp isn't even close to interfering.

The gauge I'm using is a 3.5" dial generic shop gauge that goes from 12 lb boost to 30" Hg draw. Nothing special, but adequate for this purpose.
 
More information

More information...

The EGR Modulator valve got toasty again. The tube from the EGR to the bottom of the modulator valve had split and was spewing exhaust past the now melted bottom tip of the EGR modulator. This was after using hose clamps to put a working one on after: https://forum.ih8mud.com/80-series-tech/245912-near-rth-vacuum-modulator-meltdown.html

So, I'll be ordering up a 3rd EGR modulator valve from Cruiserdan tomorrow. Why is this being such a pain? The first post SC EGR Mod valve the hose blew off and turned into a cutting torch. The second one we hose clamped on tight, so the hose split and it started spewing exhaust again. I caught it early enough that it didn't roast anything besides the EGR Mod valve.

Is it theoretically possible that I have too much exhaust back pressure? It has the original exhaust still. Would a clogged catalytic converter result in the EGR system spewing parts?

Would a clogged catalytic converter also explain (in part?) why my truck's got less power than a VW Thing right now?

It still wouldn't explain why I can't generate or measure positive pressure (boost) on the intake.

Hmmm... Looking for ideas guys.
 
Cat 1 is welded onto the Y pipe... I can drop my slider and break it apart between cat 1 and cat 2...

How do I bypass cat 1 short of ramming a piece of rebar through it repeatedly?
 
There is a gauge for measuring back pressure that screws into the o2 bung. I don't know where to get one or how much it costs though. Sorry.
 
Cruise4070 had this problem with his 80 with the hose blowing off too. The 2nd cat was clogged but the 1st one was fine so we cleared the clog out of the 2nd . bolted it all back up and its been fine for 3years now.
 
Back
Top Bottom