Sub connection

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 2, 2006
Threads
65
Messages
327
Location
NJ SUCKS
Website
www.recordme.com
I got a bass link sub which is a pretty hefty self contained unit .
I have it hooked to the leads that fed the old sub speaker in the rear coming from the OEM sub amp but something is a miss:
The line is actually microphinc" and somwhat unstable
Did not measure but there seems to be voltage in the + - speaker
line as well .crap city.
I have the schematic for the oem sub amp connections but it s hard for a 1/4 banna to deciepher
It looks like the sub amp gets fed by a combination of the l/r rear speakers rather than a line from the head unit Not what i was hoping for
Any one have any input(no pun) on the best way to use the existing connections to the oem sub to feed the new beast ?Wire color would be awsome
TX to all who read this whole boring thing:)
D
 
If you have an aftermarket head unit, I would just run a new RCA direct, do not run it near the power wire though.
 
I used the old door speaker to bridge the connections an figure out which wires to use. That worked fine but as with all line level connections the sound quality or volume was not there. I ended up using a cheap line level convertor right off the factory sub plug.

If you need to know which wires they are I can check later.
 
As firetruck says, run new wires. Run a new power wire from battery(with an inline fuse/bridge breaker), on/off lead & signal (RCAs) from head unit & ground (as close to the amp location as possible). Run power down one side of vehicle and the signal wires down the other side.

Take your time, not hard and if done correctly, you will never have to touch it again!

Good luck,

Riley
 
do you have the factory head unit?
Yes I do
I figured out the l/r +/- speaker wires just now and it s so so
not a lot of gain
you'd think if there is a factory sub they would do it the right way and provide a discreet out right from the head unit
Usually IMHO jumping the speaker wires to feed a sub is sort of a rig job done out of necessity to retofit one.
Anyone know what the male molex connector(about 8 wires) not going to anything behind the rear taillight by the factory sub speaker is for??
Weird.....
TX to all for the assist
 
Last edited:
Its believed to be for lights on the ambulance doors sold overseas.
Let me get this straight.
The basslink has its own amp.
You should be taking the lines going into the amp (not out) and connecting them to the basslink. (non amplified input)
I assume you will need a little bigger gauge wire connecting to the battery directly and a remote on/off line should already be connected to the old stock amp so just reuse it.
 
Its believed to be for lights on the ambulance doors sold overseas.
Let me get this straight.
The basslink has its own amp.
You should be taking the lines going into the amp (not out) and connecting them to the basslink. (non amplified input)
I assume you will need a little bigger gauge wire connecting to the battery directly and a remote on/off line should already be connected to the old stock amp so just reuse it.
The bummer is that they tap the rear speaker lines to feed the factory sub amp
Of course the bass link has a skpr level inputCrutchfield Advisor - Subwoofers - Infinity's BassLink vs ...

I did figure out all but 1 on the wires that go to the sub amp but you make me think maybe that s the remote switch for it....
Tx for the input
Dan
http://www.crutchfieldadvisor.com/ISEO-rgbtcspd/reviews/20040413/bass_reviews.html
 
I'm having sort of the same issues with a Kenwood Powered Sub I got for Christmas. I have the FSM and am trying to figure it out from that. I'll let you know if I have a brain storm as electrical is my shortcomming. My directions say to tap into the front speakers for signal and run the power from the battery with a 10 amp fuse and a wire to a switched circut for acc power. Looks like to me, from the wire specs that the sub is tied in to the rear speaker & roof LH with B&Y (blue and yellow?) and to the rear & roof RH with R&W (red and white?). The sub power looks like it comes from 3 wires, Y (yellow) running to the main amp in the #6 slot in the connector, G-R (?) Runs to the 15 amp CIG which goes to the ACC in the ignition in the fuse block and the third runs to the main amp R-B (?). Does that make any sense at all?
 
I'm having sort of the same issues with a Kenwood Powered Sub I got for Christmas. I have the FSM and am trying to figure it out from that. I'll let you know if I have a brain storm as electrical is my shortcomming. My directions say to tap into the front speakers for signal and run the power from the battery with a 10 amp fuse and a wire to a switched circut for acc power. Looks like to me, from the wire specs that the sub is tied in to the rear speaker & roof LH with B&Y (blue and yellow?) and to the rear & roof RH with R&W (red and white?). The sub power looks like it comes from 3 wires, Y (yellow) running to the main amp in the #6 slot in the connector, G-R (?) Runs to the 15 amp CIG which goes to the ACC in the ignition in the fuse block and the third runs to the main amp R-B (?). Does that make any sense at all?


Photogod, do you have an aftermarket headunit? If so, just get a amp/subwoofer wiring kit (order from Crutchfield etc.) and run all new power (directly from battery and ground near the amp location) and signal (RCA out the back of the headunit) to the new subwoofer. If running the factory headunit, then use the signal leads that go into the factory amp but still run new power and ground wires to the new sub/amp. Trying to run the new amp/sub power from factory wires will not be the best option. Subs require a lot of power and need to be fed with the largest power wire you can use (10 gauge minimum). I have not looked at the wiring to the factory sub, but I know it is no bigger than 18 gauge (if that).

Riley
 
I'm having sort of the same issues with a Kenwood Powered Sub I got for Christmas. I have the FSM and am trying to figure it out from that. I'll let you know if I have a brain storm as electrical is my shortcomming. My directions say to tap into the front speakers for signal and run the power from the battery with a 10 amp fuse and a wire to a switched circut for acc power. Looks like to me, from the wire specs that the sub is tied in to the rear speaker & roof LH with B&Y (blue and yellow?) and to the rear & roof RH with R&W (red and white?). The sub power looks like it comes from 3 wires, Y (yellow) running to the main amp in the #6 slot in the connector, G-R (?) Runs to the 15 amp CIG which goes to the ACC in the ignition in the fuse block and the third runs to the main amp R-B (?). Does that make any sense at all?
I just got done figureing it all out you need to disconnect the factory amp and cut the wires which are exrtentions of the rear speaker feeds
too much to type would you like to PM me your phone I d be glad to explain it all to you
Dan
 
Good,
Cut speaker leads and reconnect to amp.
Run your own power line (use what the manual says)
Remote on you can use the blue or blue/white
Glad you got it figured out.
Its amazing how easy that dash around the HU comes off.
 
Back
Top Bottom