Stupid question but need some help...

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 20, 2010
Threads
49
Messages
701
Location
Socal
Hi,

I have a read a ton of threads about drive line grinding on decel or when the pedal is floating after a lift and did what was suggested. I took off the front drive shaft and drove around and bam, the grinding was gone so it looks like a new front drive shaft is in my future.

As is the norm, I missed the groupbuy for a tatton driveshaft, but such is life. Here are my questions:

1) Is the general consensus the actual grinding is the needle bearings in the U joint as I want to make sure I'm not somehow impacting the front input shaft to the transfer, although I am not sure how that could be.

2)Also, this didn't start right away, and didn't improve with grease, so the obvious next step is a DC drive shaft. Has anybody else had this develop ~500 miles after a life?


Thanks guys/gals, sorry for the stupid question, but I have a 800 mile trip in a bout a week and might not have time to get the drive shaft so I wanted to understand the impact.

Vibration grinding sound after 3-inch OME lift--drop transfer case????

Noah
 
This lift is under 4", it is 75mm slinky coils...the no drive shaft no issue test seems pretty conclusive:)
 
I had the same issue, turned out removing the front driveline was the cure. So I had a DC front made and installed it....came back. Turns out the culprit in my case was the rear at the diff. The driveline yoke and the pinion flange were contacting each other. Food for thought. I would suggest marking the ears of your drivelines with a paint pen or the like and going for a drive with a few decel spots and checking for contact before going and buying anything.
 
@LandCruisinMy93 thanks man, that is a good idea, I will do it tonight.

@NLXTACY I have slinky 75mm coils with Slee castor correction plates.

As I mentioned, I am going on a ~800mile trip on July 6 so am trying to at least come up with a risk mitigation plan by then. I truly appreciate the feedback and input and will happily read more threads if someone wants tp point me to additional info
 
My boss in the USAF used to say, "The stupid question is the one you don't ask". I have 4.5 lift, when I had the caster correction bushings, I had the vibration, BTW I dont like those caster bushings. Took them off, installed MOOG control arm bushings, with the Man-A-Fre Drop brackets, vibration gone. If you removed the front driveshaft and the vibration was gone, maybe your driveshaft is out of phase.
 
could also just be one bad u joint, sometimes they go bad due to an internal clog in the grease passages. I grease mine regularly but had a u joint go bad because of that, needle bearings were gone in just one cap the other three were fine
 
I agree on checking the u joints. That isn't a ton of lift. My 80 with Slee 4" needed the DC front (made one out of 4runner driveshaft) and my daughter's with OME heavy + 1" spacer is fine, go figure. The buzz is either a u-joint or out of phase from caster correction if truly from the front. A u-joint is a ton cheaper and good maintenance. Here's a good video on phasing.

 
Last edited:
Thanks for the video! If the driveshaft was out of phase, woukdnt the noise be constant regardless of speed? I only have an issue when i take my foot off/put it on the gas 2300rpm to 2200 rpm and vice versus. I reased the u joints but no luck, I guess I can replace them next to save some $!!!
 
Well, little update. I swapped both front ujoints with cheapies from the local part store (which is one of my least favorite jobs ever), but no change...I might try swapping out the rear ujoints too, but I'll use real Toyota joints for that.
 
With the vibration on decel, especially at highway speeds, sounds more like a rear shaft issue, at least in my experience.

Even with adjustable upper arms to try to rotate the axle pinion to be in phase with the output on the xfer case, I'd still get a little vibes at certain speeds. Just installed 2 new Toyota u-joints and now the truck drives pretty darn perfect. No more vibes or clunks when shifting to P-R-D.
 
Back
Top Bottom