stuck drum

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Some can be a bitch.. I have been known to split the drum with a cutting torch.. bust it with a sledge hammer.. remove the wheel cly. retaining bolts and brake line, spot weld a piece of chain to it ..hook-up a come-along attached to a post and jack the bastard off. " hair,guts,& feathers" all together... show no mercy, never look back, till it is over... then go find the replacement parts...:D
 
Did you remove the screws that hold the drum on?
Also take a wire brush an scrub the center area of the drum where it fits over the axle, then hit it with your choice of penetrating lubricant.
Did you pry up on the tab for the star adjuster on the wheel cylinder, if you don't its not going to loosen. You can tighten it without pushing up the tab, but you can't loosen it.
I've been able to get them off everytime by using the above method.
 
The drum is loose from the axle?? I believe it was in your other thread.. is the problem that the drum is worn and there is ridge in the back that won't let pass over the shoes? Try loosening the brake line to release any pressure that might be present... does your drum have the 2 threaded holes in it ? if so.. those are for pusher bolts...
 
The shoes appear to be binding on the drum, as I am unable to adjust with the leaking wheel cylinder. I have depressed the locking tab but cannot make the star adjuster move. It would seem that it has not been removed for some time. If I could adjust the shoes so that the drum didnt drag I think I could get the drum off with a bit of persuasion. I'm not used to drums with internal adjusters, but am sure my technique is OK (compared it with other side).
 
Well since the wheel cyl. is leaking there shouldn't be any pressure to worry about...if it has the 2 threaded holes in the drum... screw in 2 bolts to apply pressure and bang around outer drum surface w/a hammer... if no threaded holes are present.. take a large screwdriver or prybar and insert it between the drum and backing plate and pry, at the same time use the hammer method.. if it starts to move, insert a prybar between the axle & drum and get some leverage there....
 
Ok simple question, Can you wiggle the drum AT ALL? If the drum is already loose then the only thing holding it is the lip on the drum edge that is catching the shoes. Remove the brake line from each wheel cylinder. Remove the bolts from each wheel cylinder. Use BFH to knock drum off. With the cylinders loose it shoudl come off with a few minutes of beating.

Then rebuild or replace BOTH wheel cylinders on this wheel and the other wheel or convert to disks. I run all drums and like them fine. Don't forget to use anti-sieze on all the adjusters so they don't freeze up again.
 
I have beat a small screwdriver in between the drum and the axle. This forces them apart, abeit somewhat crooked. Don't use a good screwdriver cause it will be junk when you're done. To get it out I have had to grab the metal part of the screwdriver with Visegrips and hit them with the BFH. It ain't pretty. I sure do miss this now with 4 wheel disk brakes.
 
BFH, long handle Maxi sledge maybe. I would heat it with a propane torch first. Show no mercy! GL- Junk
 
Coolerman

The drum will not budge - no movement at all. I cant be sure that the w/c is leaking, but I'll get the 8mm bolts and take to the drum with a BFH. Is there any benefit in removing the w/c bolts in this case?

Justin

PS thanks for all the help so far everyone
 
Coolerman

The drum will not budge - no movement at all. I cant be sure that the w/c is leaking, but I'll get the 8mm bolts and take to the drum with a BFH. Is there any benefit in removing the w/c bolts in this case?

Justin

PS thanks for all the help so far everyone

Whale on er with a big sledge.
 
Coolerman

The drum will not budge - no movement at all. I cant be sure that the w/c is leaking, but I'll get the 8mm bolts and take to the drum with a BFH. Is there any benefit in removing the w/c bolts in this case?

Justin

PS thanks for all the help so far everyone

Some times the drum will rust weld itself to the axle flange. That's the reason everyone is telling you to use brute force on it. Try just smacking the crap out of it a few times just to see if it will break loose. If it doesn't the I would remove the W/C bolts and brake lines then start back with the hammer. By removing those bolts and taking pressure off the shoes you can FORCE the drum off taking the shoes with it. I had to do this exact thing to mine. I was sure I was going to literally shatter the cast drum I was beating so hard. It finally started inching off.
 
did you break the drum with the sledge, or just break it free?

broke mine free with a nice BFH. As stated it rusts right around that lil flange and a BFH will break the "Rust Weld" free after awhile. I found that beating on the outward face (without hitting the flange or wheel studs) works very nicely :cool:
 
Back
Top Bottom