Stuck caliper piston

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

I recently had this problem on my truck. I was changing out the front pads and one of the pistons refused to go back in. I unbolted the caliper, but did not disconnect the brake line, and turned the thing upside down then right side up, then the caliper went back in again very easily. I can't explain why this worked, but it did.
 
Use a "C-clamp" or what ever else works, I open up the brake fluid resevoir cap and then compress the piston with a clamp, then pump the brakes in order to push the piston out. Now try cleaning up the piston with penetrating fluid ... I used an old tooth brush then lubed her up. Repeat the compression and extention process on the caliper piston till you are confident of smooth operation.

Good info from all;

Squash; you mentioned cleaning the pistons up while on/in the caliper using penetrating fluid;
sounds like a logical process, however; could that petroleum based fluid interact with the brake fluid and/or seals negatively? ie: if it gets by the piston, or not a problem??

I'm having a hard time sourcing calipers; no one carries them in stock except cruiser parts in NH; they have rebuilds for $89 each, no core. My plan was to have both calipers on hand in case I cannot get the piston(s) back in after opening the bleeder screw, tilting, banging and otherwise pleading for it to move.

Anyone ever buy rebuilds from them or know anything about the cruiser parts.net reman calipers for an 80??

Also, Advance carries a premium line; Arney-Beck? ditto; none in stock, but about $80 each semi-loaded.

Was not aware that Toyota sold remans for the 80 after 95?? Last I checked/heard only new were available for models made after Sep 96??
 
Last edited:
As your pads wear the pistons have to extend further out hence the reason you will see low brake fluid in the resevoir. When you change your brake pads the pistons are now pushed back into the housing and because of exposure over time the outer ends may end up with some scale or rust depending on your driving and climate.
This deposition is what interferes with the pistons ability to travel freely, sometime the process of "c-clamps" and pumping and releasing the pistion is enough, otherwise dig in and clean.
From here you decide if this works otherwise order new or remans.

If you suspect your calipers are dragging carefully feel your wheel hubs for "heat" use the other wheels as baseline.

I did my last clean up on a rear caliper in the snow with tools from my bag, you do not have to remove the hose, just tie up the caliper.

https://forum.ih8mud.com/80-series-tech/175627-brake-caliper-rebuild.html

Rebuilding Front Calipers
 
Last edited:
Put in new pads today; No stuck caliper piston as "diagnosed" at the Toy stealership (huffing and puffing mechanic with a C-clamp, but actually applying no real extra pressure to the piston as I watched). We had no problems pushing the pistons back at all today (while outside in front of the barn other than the windchill factor). We just used a large screwdriver between the pad and rotor to get them back a tad after removing the clip and spring, then shoved a short pry bar between the pad and the rotor to push them all the way back. Then when pushing back the opposite side, used the pry bar for that pad while holding the already pushed back pad/piston with the large screwdriver; easy. Only thing were the big dents on one of the pistons where the mechanic hit it with his hammer to show me that it was stuck (Hey, can you back up the turnip truck? :rolleyes: ). On the other hand, I noticed that the right front pads were significantly thinner (more wear) than the left front pads. Also, one of the left front pads was wearing faster on one end than the other. Both of these tell me that the pistons are not moving evenly and/or not retracting properly. So, new calipers are in order soon, but these new pads will get me home. Thanks to all.
 
Last edited:
Also, one of the left front pads was wearing faster on one end than the other. Both of these tell me that the pistons are not moving evenly and/or not retracting properly.

The uneven wearing of your brake pads is due to a stuck piston in the calipers.

-B-
 
Back
Top Bottom