Stereo Install Help (real time) & Intro

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 31, 2007
Threads
15
Messages
100
Location
Edmonton, Alberta, Canada
Been reading the forums for a while. Now I'm in need of a bit of help, so I thought this would be a good time to do my intro as well.

Here's a quick shot of my '91 HDJ81 (TD w/ air lockers):

cruiser010.jpg


I've got the deck out right now and just started wiring in a new one, but I can't get it to power on. I took a volt meter to it and the power wire isn't getting any voltage (okay, 0.01v). The ground seams to be fine and the ignition 12v is getting a legit 12v. I just checked the DOME and CIG fuses, but both of them are fine (replaced anyways, for good measure). Would anyone have any ideas as to where I could start looking to see why the power wire isn't getting 12v?

Thanks in advance,

Corey
 
Welcome :flipoff2:

Nice looking rig!

As to your problem, for some reason I'm thinking there is another (or more) fuses you need to check, and not in the dash area but under the hood. Something I recall reading but I'm wrong more often that right :)

EDIT: Not sure if this will help or not and not sure if it only applies to FZJ80s or also to FJ80s

http://homepage.mac.com/dfmorse/FuseChart3.5.1/
 
Last edited:
You should be using the ignition wire for the stereo's main power.

Was the key on or off when you tested positive for 12v?
Not usually.


Most stereo main power (often the yellow lead) comes from constant +12v. The red lead is usually connected to the ignition 12v source.
 
Not usually.


Most stereo main power (often the yellow lead) comes from constant +12v. The red lead is usually connected to the ignition 12v source.

Oh. Right. :whoops:

I'm not having a good day....
 
Wait, doesn't the constant 12v serve as a memory? like stations presets and such?
 
Constant 12v both serves to provide the HU with power for its memory (although a few use stateful memory, and some have capacitive circuits to survive outages) but I believe the real purpose is to draw the majority of the power (for amplification) off of a more robust circuit than the ignition lead.
 
Constant 12v both serves to provide the HU with power for its memory (although a few use stateful memory, and some have capacitive circuits to survive outages) but I believe the real purpose is to draw the majority of the power (for amplification) off of a more robust circuit than the ignition lead.

Ah, gotcha, I never knew that. Similar to a relay?
 
Ah, gotcha, I never knew that. Similar to a relay?
Same principle, yes sir. Nategator has it down.

Thanks guys for all the comments, btw! :beer::flipoff2::beer:

Corsair, the DOME fuse is under the hood and the CIG fuse is beside the steering wheel. I tried grounding the ignition +12v and the constant +12v and both fuses blew only for the ignition +12v. IIRC, those are the only two.

In theory, the constant +12v should route to one/both of the fuse blocks, then to the battery... but I'd have no idea where these wires run. Anyone have a wiring diagram/the service manual? I didn't manage to snag a copy before the link went down.

Cheers!
 
Are you sure you have the right wire? Have you tested any others for 12 V constant?
 
Thanks Slinger for the reply. I'm quite sure I do, yes sir. I say this as it is the wire that matches up to the 12v constant on the aftermarket harness and is also where it should be on the factory harness. Not to say I'd solely trust that though, so I did test all other wires on the harness and the only wire on the factory harness producing the 12 volts was the ignition. The small harness I neglected to test as it's solely for the rear speakers, IIRC.

BTW, what do you ride? Looks sharp.
 
Last edited:
So, the only solution I could come up with was to wire in a new constant 12v wire either straight from the cig/dome fuse block, or straight from the battery, as there are already 3 and 15 amp fuses inline, on the deck's harness.
 
Run a 12v constant from somewhere in the cab, it's a whole lot easier to do.

If you end up running a wire from one of the batteries, make sure you fuse it AT the battery. I learned the hard way...
 
Back
Top Bottom