Starting Issue - No Crank

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 6, 2017
Threads
10
Messages
74
Location
S CA
Wondering if anyone may have an idea about my starting issue -

It's extremely intermittent, usually my 95 starts up right away no problems, but occasionally, I'll turn the key to crank and I'll get absolutely nothing. Seems like sometimes I get a faint single audible click but sometimes just nothing. New battery is fully charged up and strong.

In other instances, occasionally I'll turn the key and hold it there and there seems to be a split second to one second lag before it cranks, as if it doesn't respond immediately to the crank command when I turn the key.

Again, extremely intermittent and doesn't seem to be temperature dependent. Sometimes it'll do it cold, sometimes it'll do it when it's just been driven and completely warm. Usually I just turn the key again once or twice and it fires right up.

Any help is appreciated. Thank you
 
Could be starter contacts. Mine did this on occasion for a while, then gradually got worse until it would not start unless I smacked the starter with a 2x4. Ended up replacing the whole starter as contact replacement didn't do anything.
 
Yep, likely the starter contacts/plunger. I had this happen recently and replaced contacts/plunger that I had on hand for just such an occurrence. Initially it would not crank (usually when colder and after overnight) a few times, then it cranked and wouldn't stop cranking even with the key to off - i.e. the plunger/contacts had welded together temporarily. Fortunately I was in the 'repair' mode when that happened since this was on the driveway with hood already up and spanners on hand so I could quickly disconnect the ground cable at the battery.

I'd suggest you resolve the problem sooner than later...

Search and you'll find info on replacing contacts/plunger - I have a writeup from years ago (so I'm well versed on the process :) ) on my site, see sig below.

cheers,
george.
 
  • Like
Reactions: ppc
@051009 Did you find a fix? I just stepped out of the office to go home and truck won't crank. Trying to think my way through the troubleshooting steps. So far this is we're I am:
1) CEL comes on
2) I can hear the imobilizer relay clicking off so don't think that is the issue.
3) Won't remote start either so not the ignition switch
4) Lifted hood and tried remote start - silence - no clicking - nothing.

I have tools but I am in a suit

I have jumped straight to Step 6 to think things over. Anything I should check / Try next before having it towed home?
 
If you are sure battery cables are nice and tightly secure on their clamps, then give the starter motor a reasonable wack with a hammer or long metal rod or call your AAA equivalent and get them to wack the starter motor for you... Worth a try. Might try to jiggle the shifter (there's the release slot for using a screwdriver to release the shifter) in case the neutral start switch isn't detecting that the shifter is in park.

cheers,
george.
 
@051009 I have jumped straight to Step 6 to think things over.

Nothing substantive to add but I admire your order of operations :). If more of the world approached problems this way we just might be better off...
 
Fusible Links
Battery Cables loose or rotted
Started Solenoids dead: Replace starter.
 
Got back from step 6 and she started right up first time.. I hate troubleshooting intermittent faults :bang:
 
I had intermittent no crank/no click (from solenoid) when cold. It went from that to starter cranking continuously even with key to 'off'. This over the period of a couple or so weeks...

I'd suggest that it is quite feasible what your starter solenoid contacts are on the way out. When was the last time you changed contacts or put a new/refurb starter in?

cheers,
george.
 
Never done either. I am pretty sure the starter is the original from 24 years ago. I think I will throw some new contacts at it for peace of mind.
 
I changed the starter and so far so good. Had a spare starter sitting on the shelf of unknown pedigree but so far in the past 2 weeks I haven't encountered the dreaded click/no start.

And I apologize but what is step #6? I only saw steps 1-4 from your post above.
 
I changed the starter and so far so good. Had a spare starter sitting on the shelf of unknown pedigree but so far in the past 2 weeks I haven't encountered the dreaded click/no start.

And I apologize but what is step #6? I only saw steps 1-4 from your post above.


Step #6 = :beer:
Step# 4 = in a sock.
Step #6 = :beer:

Hence, the term...... 646
 
This is how I usually go about a no crank or intermittent no crank.

1. Battery voltage 12.4 or higher?

If no, charge battery.

Keep in mind, batteries can go from 12.4 or higher to 'dead' under load. Good idea to read voltage under load as well. Load test is 1/2 CCA for 15 secs should not fall below 9.6 at ~70* ambient temp from a fully charged batt of 12.4v or higher. Have battery load tested if suspected issue. I had the stock 5yr old batt in my Tacoma go from 12.7 to 3v when trying to crank and back to 12 something.

The lazy way to test, if you can get it to crank, is just make sure it doesnt fall below 9.6v while cranking. Not fool proof but usually weeds out a bad batt. If you doubt the battery just take it to be load tested.

If Yes go to step 1b.

1b. Does battery drop rapidly with any load applied to it?

If yes, remove, charge, and load test batt. See above.

If no, move on to step 2.

2. 12 volts to solenoid at starter from ign when turned over? If yes go to next step. If no, diag ign circuit.

3. 12 volts to starter from batt? If yes go to next step. If no, check your connections.

4. While turning over key do a voltage drop test from + post to starter + post
And then do Voltage drop test from starter case to - post at batt. Is voltage drop less than .3 volts?

If no. Voltage drop test between each connection until you find source of voltage drop. Post to cable clamp, clamp to exposed cable or other end of cable, etc... ideally youd see no voltage drop art any connection. Clean or replace until voltage drop is very minimal. Easy way to find poor or bad connections, and in my experience this is what causes cranking issues most of the time.

If yes move on to next step.


5. Beat on starter with hammer. Does it start? If yes, replace or rebuild starter. If no, remove and have starter tested.
 
Incidentally you can check your charging connections the same way. Batt - post to alt case or ground and batt + to alt output, while running/charging.

Voltage drop test is kind of like ohm testing but all an ohm test will tell you with batt cables is usually if you have a connection or not. As long as a little bit of the circuit is connected properly the ohm test will show low resistance but this really tells you nothing. Voltage drop however will tell you what kind of resistance is taking place across the whole connection. Which is why theyre useful for things like starting charging circuits where were dealing with larger cables and connections.

Voltage drop tests must be done with a load on the circuit.


Just fyi.
 
Last edited:
Was able to do most of that - at least steps 1-3. I have dual batteries and have 2 volt meters on my starter battery. Both were reading 12.6v.
I had planned to check the volt drop when I came back from the pub but it fired right up. I will order up new contacts and try and fit them over the weekend.
 
Was able to do most of that - at least steps 1-3. I have dual batteries and have 2 volt meters on my starter battery. Both were reading 12.6v.
I had planned to check the volt drop when I came back from the pub but it fired right up. I will order up new contacts and try and fit them over the weekend.
Sounds like thats probably your issue, just figured I'd throw that all out there for whomever.
 
Neutral safety switch maybe. Mine was doing this over the winter. I would turn the key and get nothing but a lit up dash, but shift to N and it would fire right up. Pulled the wire harness on the side of the transmission, cleaned with electrical contact cleaner, regreased and plugged back in. No problem since.
 
Back
Top Bottom