Snorkel Install...at last

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 4, 2006
Threads
47
Messages
899
Location
Mineola, TX
Well, after letting it ride around in the back of my truck for the better part of a month, I finally got around to punching some holes in my fender and installing my snorkel.

Here's "The Anchor", so sweet and unsuspecting, with no holes where god didn't intend them to be.
dsc00499jr7.jpg



Step one, get my tools ready, and lay out all the parts to be sure I wouldn't get halfway done and then realize something was missing.
dsc00498ne2.jpg



Luckily for me, good ol' #70 inspected this snorkel, so all parts were present and accounted for.
dsc00500ba1.jpg



Step two, remove the intake. I didn't have a photo assistant for this, but here's what got taken out.
dsc00501ov6.jpg



Any idea what this is? It was behind the pass through portion of the intake, inside the fender. It was rendered useless by the removal of the stock intake, so I took it out.
dsc00502kg2.jpg



Enter lovely assistant to help tape on the template. TRUST THE TEMPLATE!! I did, and had absolutely no problems. Just line it up to the top of the fender, where it meets the hood, and the back of the fender, where it meets the door.
dsc00505mg6.jpg


To be continued...
 
Continued

Well, template on, drilling points taped to prevent damage. Time to drill the pilot hole for the big hole. Notice the cardboard over the fender flare, just in case the hole saw tried to kick out or run.
dsc00506ib5.jpg



Okay, now for the big leap from can I do it to hell yeah. Note: I did have to extend the center drill bit on the hole saw so that it would reach the pilot hole, as it sits right in the dipped in area of the body line.
dsc00507de1.jpg

dsc00508aa6.jpg

dsc00510tw6.jpg


As you can see, my photo assistant got a little excited about snapping the pics during the hole saw portion of the install. After that, she went in, so I'll tell you what came next. I put the template back down and checked it against the snorkel. then I proceeded to mark and drill the rest of the holes according to the template.

Now I dry fitted the snorkel onto the fender.
dsc00511ln0.jpg



Looking good
dsc00513xh3.jpg



REWARD!!
dsc00515rz4.jpg
 
looks great. Nice help, I had my girlfriend do the complete install of my snorkel. I just sat back and ate some white castle and watched her. It was a sign of faith letting her take an air wheel to the sheetmetal :flipoff2:
 
More

Reward part deaux!
dsc00514nt1.jpg



Marking the stabilizer plate (is that what it's called) on the A-Pillar. I attached the stabilizer plate to the snorkel and used a white out pen while the snorkel was dry fit onto the truck to mark the plate position so I could mark out where to drill the holes in the A-pillar once the snorkel was off. That's what this pic is.
dsc00518hw0.jpg



Holes marked on A-Pillar.
dsc00520ln9.jpg



Drilling the A-Pillar. I just used the provided nylon nutserts and sealed them up w/ a little silicon. I plan to replace these w/ some rivnuts later on.
dsc00522ax5.jpg


At this point, I totally lost my photographer. Basically, I just made sure all the holes were deburred, primed and painted them to prevent rust (I used a q-tip to apply), and bolted everything into place as it was when dry fitted. I didn't install the two farthest back stud/nuts inside the fender, but plan to do it when I rebuild my broken antenna mast sometime soon. My arms aren't spindly enough. I think I'll drop the inner fender so I can get to them more easily. Anyone have any thougts on this?

Okay, so that's it. I started at about 4:15, and was cleaned up and ready to go to Hooters by 7:45. This was my first install of this kind, and I think it would have taken this one :banana: alot longer if it wasn't for the other writeups people have done in the past. Thanks to everyone who posts up to help us all out. I just hope someone finds this useful when they do their install.

:cheers:
 
Didn't do it yet.

I didn't install the two farthest back stud/nuts inside the fender, but plan to do it when I rebuild my broken antenna mast sometime soon. My arms aren't spindly enough. I think I'll drop the inner fender so I can get to them more easily. Anyone have any thougts on this?
:cheers:
 
Brilliant writeup! Best one I've seen. Thanks man. :)
 
Nice write up. Pretty simple and straight forward.

Congratulations on your wedding by the way.

Cheers :beer:

Doug
 
Good writeup Jason. Congrats on the snorkle, wedding and happy B-Day.

Buck Buchanan
 
Thanks guys, I really enjoyed putting this on and doing the writeup. Also, I love the result.

SOCALFJ,
The two rearmost bolts are about halfway between the antenna and the rear of the fender where it meets the door. See pic 2 in post #4 for a visual. They could probably be accessed through the antenna access hole but since my arms aren't exactly skinny, my SO isn't so good w/ a wrench, and I plan on doing the repair to the power antenna mast soon, I opted to wait. It seems like you could almost omit the use of the two studs in this location if you wanted. That'd be a judgement call you'd have to make, but if I did it again, I would have drilled two less holes in the fender.

:cheers:
 
Next up is probably new tires and some gears (4.88). I'm also considering some 1.25" or 1.5" wheel spacers.

For tires, I'm looking at the Cooper Discoverers STTs. I've been looking at Trail-gear for the spacers.
 
Back
Top Bottom