shaving the head

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 27, 2006
Threads
73
Messages
1,335
Location
Gladstone Qld
shaved head/ TBI questions

i searched but did not find.

1, can i shave the head of my 2F without having to go higher octane, if so how much?

2, will a shaved head effect the use of LPG? will it run better or worse?

3, noob question: whats a throttle body i seen it talked about but dont know what it is exactly?
 
Last edited:
cant help you on the head shave, but just to clarify a throttle body is used in a efi system like the 3fe engine your 2f is carburated.
 
ok the TBI officially looks sweet how hard would it be to install and how much would it cost?
one thing i dont like is computers in cars in the thread it has the controller in the glove box which is a cool idea so i'm eginning to like this.
 
TBI Install <---- this is a link
Serenity,

Shaving the head should increase your compression ratio which will impact the amount of octane required under normal conditions. How much is hard to tell. There may also be a way to alter the factory settings in the distributor that would allow more retard (nothing personal) at initial acceleration and an increased amount at higher RPM when detonation is less of a problem. (been a while since I thought about this and might be the other way around, more advance to launch, then retarding as rpm increases)

I think that LPG would be fine as compared to conventional gasoline when it comes to increased compression as it does not tend to detonate the way gas does

Depending on how much you cut the head, you may want to "clay check" it so you can determine if there are any potential valve interference issues.

THe throttle body of an injection system is effectively the air intake of the fuel system. Think of it as a big one barrel butterfly (like a carb w/o a fuel source) that controls the amount of air that goes into the engine. Some older systems have a regular air filter set up on top like a carb system does, but later models have cast ram tubes that feed the air to the system. THe one barrel butterfly is not on every application, but shoud give you a rudementary understanding of the term "throttle body".
 
cool thanx. i've done a bit more research and i'm gonna try and find a cruiser mechanic in my area to help me out with some of this, i think i might go the TBI install and get the head shaved a little.

will TBI work with LPG?
 
Not sure. Just depends on how you get the fuel into the body. We used to replace carbs with TBI and ran methanol (racing application) but methanol was delivered just like the gas. DOn't know if there is a way to introduce the LPG
 
damn talked to a local FI shop and they were saying it would be at least $3000 to put in a TBI. :eek::eek:

i've been reading through all the info i can find the problem is that american vehicles are different to australian so a lot of the parts you guys are talkin about either dont exist here or are called something different, so finding parts for a TBI will be a pain.

finding a 3FE to do a 2FE conversion is almost impossible where i am and rediculously expensive.

this idea is suddenly becoming doomed.
 
I think shaving he head would work fine. You can also move to a different piston and achieve the same results. Higher compression is nice as it effects the entire power band. Not sure how it would run with LPG though. Probably fine. IMHO, this would be a lot of work for fairly minor increase in power, maybe only 5%. I would save my money and focus on a nice carb rebuilt or some other aspect of the car.
 
The head on my 2F in my 60 is shaved .050. Runs fine on 87 octane pump gas. It pings a bit at elevations but I have not played with the timing. It is set at factory recomendations.

Interesting-Do you notice any extra power? Any problems passing smog?
 
LPG likes extra compression...

It has an effective octane of 105ish..
 
im looking at shaving the head cos i have a head gasket problem anyway, im planning on a carb rebuild, i have been looking at a TBI as i said in earlier posts but thats not gonna be easy to get parts where i am.

so i assume when you guys are talkin about shaving the head 0.050 you mean in inches right?

oh and my engine is a 1984 cant tell you the casting number as its at my mechanics gettin the lpg lines re-run.

anything else i should do thats not to much more effort while ive got the head off?
 
The head on my 2F in my 60 is shaved .050. Runs fine on 87 octane pump gas. It pings a bit at elevations but I have not played with the timing. It is set at factory recomendations.

what are you calling elevations? rarely get over 2000 meters in oz.
 
Back
Top Bottom