self-tightening crank nut?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 16, 2008
Threads
3
Messages
22
Location
Milwaukee, WI
Website
www.poppfitness.com
Today I replaced my front crank seal and oil pump seal (with much frustration) and finally faced the task of torquing the crank nut back on. I rented a 600 ft/lbs torque wrench but have not yet decided on the best method to hold the crank pulley while I torque the nut. I have read on here that people have used both chain wrenches and strap wrenches but I was most surprised to hear from a worker at NAPA that I don't need to do anything! He told me that I should just thread it on as tight as I can by hand and when the engine runs it will tighten itself the rest of the way. Has anyone ever done this? It sounds pretty risky to me so I wanted to ask what others have used to do this job. I am on a budget so if anyone knows a way to hold the pulley with a crow bar or has had a good experience with a strap wrench (brand?) I would like to hear about it. Thanks
 
Chain wrench on my end when I did this...had a buddy holding the chain wrench while I worked the torque wrench.
-
According to CDan, you can also use the frame as a brace for the chain wrench if you are alone.

The crank bolt is definitely not "self-tightening", though I guess you could use the power of the starter and the crank to use against the torque wrench as well.

-o-
 
Today I replaced my front crank seal and oil pump seal (with much frustration) and finally faced the task of torquing the crank nut back on. I rented a 600 ft/lbs torque wrench but have not yet decided on the best method to hold the crank pulley while I torque the nut. I have read on here that people have used both chain wrenches and strap wrenches but I was most surprised to hear from a worker at NAPA that I don't need to do anything! He told me that I should just thread it on as tight as I can by hand and when the engine runs it will tighten itself the rest of the way. Has anyone ever done this? It sounds pretty risky to me so I wanted to ask what others have used to do this job. I am on a budget so if anyone knows a way to hold the pulley with a crow bar or has had a good experience with a strap wrench (brand?) I would like to hear about it. Thanks

I used some flat bar stock from the hardware store.

239761479_6bcnG-XL.jpg


239760913_ue4TD-XL.jpg
 
Last edited:
He is full of crap. As I recall, you risk loosing your power steering and potential low oil pressure if this bolt is not tight enough. When I did mine I used two pieces of chain. Each chain was bolted to the pulley and each was wrapped an bolted (through two rings in the chain) to the frame - one on the passenger side and one on the drivers side. I tried the homemade sst trick, but found it to be a pain the arse over the chain trick. To each their own.

Karl
 
Some good ideas, I think I will go with the chain wrench. If I had an electric drill I would give the flat iron trick a shot, but I don't. I do like the chain idea also but I am picturing the AC pump pulley getting in the way, wasn't that the case? Thanks for the input.

-Zach
 
The only person I found with a torque wrench that big was a 'friend of a friend' who's a farmer. Also -- truckers will sometimes have wrenches that big.
 
That is nearly the same thing I did, but I chained up both the passenger side and the drivers side.

Karl
 
This is the best method I've seen for it:

https://forum.ih8mud.com/80-series-...bolt.html?highlight=CHAIN+oil+pump+crank+bolt

All you need is a length of chain, and the right size bolt to screw into one of the threaded holes that's already in the pulley.

What'd the rental on the torque wrench hit you for?

:beer:
Rookie2

Tried this method and worked good, so thanks. This was definitely the cheapest route considering I could not figure out the crow bar method.

I called at least 15 local (Milwaukee) places to try to rent a big torque wrench but the biggest pretty much everyone had was a 250 ft/lbs. Finally I came upon a place called RSC Rental that had one for equipment repair but not rental, but the guy sympathized with my frustration and decided to rent it to me for $29 for 3 days. I have no idea if that was a good price or not, I just knew I needed it.
 
No, the crank bolt won't "self-tighten". In fact, it will fall off if you don't torque it tight enough, I saw the aftermath on a friend's T100 a few years ago. Crank pully chewed up the end of the crank, cracked the timing cover, flew off and tossed the belts, it was about a $500 mistake.
 
No, the crank bolt won't "self-tighten". In fact, it will fall off if you don't torque it tight enough, I saw the aftermath on a friend's T100 a few years ago. Crank pully chewed up the end of the crank, cracked the timing cover, flew off and tossed the belts, it was about a $500 mistake.

That will never happen on an 80, you'll seize the motor long before anything flies off.
 
That will never happen on an 80, you'll seize the motor long before anything flies off.[/quote

I was reading some of your previous posts and you seem to know a lot about this. Anyway, it is OK to reuse the the original crank bolt right? If so, should it be torqued to the 304 ft/lbs?
 
yes you can reuse the bolt and it needs to be torqued to 304 ft lbs.

Because the oil pump and PS pump are gear driven off of the crank there is a sacrificial sleeve on the gear that is mounted on the crank itself. This gear/sleeve combination is clamped in place by the pressure created with the crank bolt. If the required pressure isn't made then the gear slips dropping the oil presure and power steering assist. The first having very negative effects on the engines longevity.
 
I know, I brain stormed for a good hour and this never crossed my mind. I was pumped to see that it works.

I'm suprised you were able to source the correct bolt so quickly. I ordered mine through Fastenal along with the stainless hex head replacement bolts.

What procedure did you use for getting the existing philips head cover bolts out?
 
I picked a couple up at ACE hardware. I believe a 10.9 grade. I bent the snot out of one, but it did the job.

For the pump cover I just followed the write up on here. I got two #3 phillips bits and tapped the screws with a hammer for a good 30 seconds and they came right out. I felt like they weren't even close to stripping, in fact I reused them. Surprisingly this was the easiest part of the job.
 
Back
Top Bottom