SCORE! (finally)

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Just as a side note, when I pulled mine out, it kinda flung out at me. The tolerances on this thing are pretty tight. I could see a truck that was burning through the last of 2 gallons of oil might gum it up enough to make the chain go un-sprung. It's a very exact steel cylinder that fits exactly into the receiving end inside the block.

A
 
IT STARTED!!!!!!!!!!!!!


Got the new battery in, and the key fob stopped all the flashing (Thank you 85Badger!).

Not all good news, it definitely had some bad noises coming from the engine bay. Sounded like a loud knocking/chirping, and then it shut down forcefully. When I turned the key again, it started again. Definitely could be bad news, but it also sounded a lot like my water pump did when it seized. At least we have made some progress. Going to take off all the belts and see if any of the accessories are seized up.

You're welcome!!!! At least for phase one.........
 
So I cut open the filter this afternoon. The motor is toast. I had a hunch it would be, but I wanted to be completely sure before diving into pulling the engine in my cramped garage. I've learned to be overly cautious ever since I rebuilt the top of the motor in my ranger a couple of years ago only to discover that the source of my overheating problem was a faulty temp gauge. Looks like it's time to start pulling this thing apart. Anyway, here's the goods.

grNyBtf.jpg


LJw9p13.jpg


PPuBG5j.jpg
 
If you think you may have to rebuild or replace anyway, I'd drive it till it craps out...you never know.

I am nervous about backing it down the driveway to turn it around in the garage. It just barely runs. I dont think driving it around is an option.
 
Well, so much for an easy fix. It looks pretty bad in there.

Are you thinking used motor or rebuild?
The problem is that the driveway is on a hill. I could get someone to push it with a truck, but I don't want to do any damage.

You might be able to attach a come-a-long point to your garage foundation or floor. I have thought about doing that at my house for the same reason. That way you could pull the truck in and out without starting it.
 
Well, so much for an easy fix. It looks pretty bad in there.

Are you thinking used motor or rebuild?


You might be able to attach a come-a-long point to your garage foundation or floor. I have thought about doing that at my house for the same reason. That way you could pull the truck in and out without starting it.


I'm not really sure. On the one hand, a used motor can be had for fairly cheap, but I feel like there is so much "while you're in there" stuff that I would want to do, I'm thinking of just getting a rebuild kit and going at it. With these things getting up in years, I would think replacing valve seals etc. on a used motor would be worth the trouble, especially with the rest of this truck being such a nice specimen. After that, rebuilding the bottom end is not that far of a stretch. Not really sure though. Going to have to browse the for sale section and see what options are out there.

I've got my eye on a kit from LCE Performance that people on the forum seem to approve of:
4.5L 1FZ-FE 1993-1997 Land Cruiser Master Rebuild Kit

I would like to go OEM but I dont know if my wallet can handle it.

I'm going to try to run it for long enough to back out of the garage and turn around and back in. If it dies, I'll just put something on my bumper and give it a push. Might turn into an excuse to get an ARB ;)
 
I'm not really sure. On the one hand, a used motor can be had for fairly cheap, but I feel like there is so much "while you're in there" stuff that I would want to do, I'm thinking of just getting a rebuild kit and going at it. With these things getting up in years, I would think replacing valve seals etc. on a used motor would be worth the trouble, especially with the rest of this truck being such a nice specimen. After that, rebuilding the bottom end is not that far of a stretch. Not really sure though. Going to have to browse the for sale section and see what options are out there.

I've got my eye on a kit from LCE Performance that people on the forum seem to approve of:
4.5L 1FZ-FE 1993-1997 Land Cruiser Master Rebuild Kit

I would like to go OEM but I dont know if my wallet can handle it.

I'm going to try to run it for long enough to back out of the garage and turn around and back in. If it dies, I'll just put something on my bumper and give it a push. Might turn into an excuse to get an ARB ;)

If you parted out the old motor and kept the parts and bought a used motor and just put the best or rebuilt parts on the used motor, that would probably be the cheapest option.

That said, you could rebuild the one you have but I would be worried about more issues because so much metal was floating around. That motor might be toast.

If you want to do the rebuild, I think Bryan's thread has the best photos and the best insight, but there are others out there.

1FZ-FE Rebuild - Restoring my FZJ80 from an early demise
 
I wouldn't buy that kit. I would buy the valve grind kit from beno or Toyota and check prices and dig a bit for OEM stuff. Onur has good pricing on all of that stuff. This is what I paid. This is a lot of stuff, and I bet there are some things like the throttle cable that you don't have to worry about. It's most of what you could do as "while you are in there". I also have a new water pump, a new alternator, fuel filter, spark plugs, oil filter, new heat shields, coolant, silicone heater hose, tape(3M, sorry Mr. T), various lubes and sprays, Probably $2000.00 total when you include the head work and hot tanking.

TOYOTA HEAD GASKET KIT 1 $275.00 $275.00
THERMOSTAT 1 $22.00 $22.00
THROTTLE CABLE 1 $140.00 $140.00
DRIVE BELT KIT 1 $25.00 $25.00
FIPG 1 $14.00 $14.00
OIL COOLER RELIEF VALVE GASKETS 3 $2.19 $6.57
OIL PUMP GASKET 1 $3.00 $3.00
FRONT CRANK SEAL 1 $18.00 $18.00
PCV AND GROMMET 1 $11.50 $11.50
PCV VENT HOSE 1 $13.50 $13.50
VALVE COVER VENT HOSE 1 $19.50 $19.50
EXHAUST MANIFOLD STUDS 13 $1.64 $21.32
LOCK NUTS 13 $1.70 $22.10
TIMING CHAIN TENSIONER 1 $28.00 $28.00
SPARK PLUG COVER SCREWS 4 $0.95 $3.80
MANIFOLD BOLT 1 $1.89 $1.89
Y-PIPE STUDS 4 $7.87 $31.48
Y-PIPE LOCK NUTS 4 $1.95 $7.80
OIL PRESSURE SENSOR 1 $60.00 $60.00
LOWER HOSE 1 1 $13.00 $13.00
LOWER HOSE 2 1 $18.00 $18.00
HEAD BOLTS 14 $17.50 $245.00
Subtotal $1,000.46
Shipping/handling $42.51
Total $1,042.97
Amount Paid -$1,042.97
Amount Due $0.00 USD
 
My engine spun bearings at 196k...10k miles after I purchased it from a fellow mudder...and I paid way more than $1100 for it.

I opted for the engine replacement, mainly for ease and the situation I was currently in (on a 2 month camping vacation with my family).

Put on a all new gaskets and installed it. I'm not smart enough to rebuild :)

Good luck with whatever route you choose. It helps that you got the truck at such a great price and it's in good shape otherwise.
 
My engine spun bearings at 196k...10k miles after I purchased it from a fellow mudder...and I paid way more than $1100 for it.

I opted for the engine replacement, mainly for ease and the situation I was currently in (on a 2 month camping vacation with my family).

Put on a all new gaskets and installed it. I'm not smart enough to rebuild :)

Good luck with whatever route you choose. It helps that you got the truck at such a great price and it's in good shape otherwise.

I think some wise person said that the rate for a good 80 is $6000 American. You either pay it up front or you pay on the back end. The good thing about getting a good price is that you can spend the money to rebuild it, knowing that the market supports it. Plus, you'll know everything on the truck by the end of it and it will be brand new, realistically. You don't have to worry about the degradation of things due to corrosion and your truck will likely be worth quite a bit more than $6000 in a few years and with new drive train, I think that would catapult its value. As a guy that searched a bit before I made my deal, if you can get a turn key, rust free truck that has been rebuilt to Toyota spec with Toyota parts, that instantly makes it worth at least $12,000. Add the lockers and the price only goes up on ebay.
 
Maybe I'll just drop a donor motor in it to get it back on the road and spend a few months rebuilding this one in the garage. Pulling it twice isn't the end of the world. Beno is right up the road from me, so I'll have to give him a call soon. If any of y'all have a running engine for sale let me know.
 
My engine spun bearings at 196k...10k miles after I purchased it from a fellow mudder...and I paid way more than $1100 for it.

I opted for the engine replacement, mainly for ease and the situation I was currently in (on a 2 month camping vacation with my family).

Put on a all new gaskets and installed it. I'm not smart enough to rebuild :)

Good luck with whatever route you choose. It helps that you got the truck at such a great price and it's in good shape otherwise.

This is what I ended up doing. Blew head gasket, found out the head was warped too much to mill, spent 4K on brand new oem head and all valves etc just to find out 1500 miles later I got a knock on the bottom end. Pulled a running motor out of a friends wrecked cruiser, did all gaskets and seals, threw it in. Works fine.
 
Maybe I'll just drop a donor motor in it to get it back on the road and spend a few months rebuilding this one in the garage. Pulling it twice isn't the end of the world. Beno is right up the road from me, so I'll have to give him a call soon. If any of y'all have a running engine for sale let me know.


I wouldn't even worry about the old motor. Just scavenge as much off of it as you can and take everything else off and label and store it. The truck is a driver, it's not worth knowing that it's a numbers matching truck. Keep all of the sensors, etc. Sell the block as a core and hope the head has a bit of value beyond scrap.
 
I wouldn't even worry about the old motor. Just scavenge as much off of it as you can and take everything else off and label and store it. The truck is a driver, it's not worth knowing that it's a numbers matching truck. Keep all of the sensors, etc. Sell the block as a core and hope the head has a bit of value beyond scrap.

Yea, I think that's the plan now. Swap thread coming soon!
 
Back
Top Bottom