rusty rig

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 12, 2008
Threads
64
Messages
522
I have a 97 that has some rust, I want to do it 'right'. all rust removed, cladding removed, holes welded and then lines tan and OD green.
I do have some rusty rockers and a bit on the top of the rear hatch window.
truck needs some maintenance, due for a birf pack and brakes all around, needs a new exhaust. engine has a new HG and is strong, it is mechanically sound.

Am I better to buy a rust free unit ( maybe with a bad engine) from the south west and transfer my parts over or repair my old lady?

Cheers P
 
If you have to ask, I would say that, in your case, getting a rust free unit is the way to go.
I bought my first 80 on a phone deal. I drove to Santa Barbara to haul it home even thought it ran and drove well. I noticed it had some rust due to the salt water environment so I talked the seller down another $500 and hauled it home against my better judgement. Over the next couple months I discovered more rust here and there. Though it was not super serious, I did not want to deal with it because I'm a nuts and bolts guy not a body mechanic. So I sold it to someone who had no reservations about the rust and bought a clean CA 80. Sounds like you have reservations.
 
I do, I know this truck well and is has served me well, but I just discovered rot in the front part of both rockers under the lx cladding.
 
Buy a solid rig with a bad motor/trans or whatever you can afford. Then you will have two trucks to build one and lots of extra parts to save for yourself or sell for a few bucks. I HATE RUST!
 
Im thinking this is a summer project, will start putting it out there that I'm looking for a rig, does not need a drive train as I have locker axles , and a good tranny and motor
 
I recently had to buy another 8O because I rolled that nice clean one I spoke of. I confered with the crew here on Mud and I was strongly advised to buy a complete 80 and go from there because of the daunting logistics of a body swap. Now I have two good drive trains and tons of parts. Eventually I will get a pretty penny for the elocker axles that are in the replacement rig. Mine already has 4.88's and ARB's. You can always keep running what you have while you save cash and continue shopping for that great deal. They are out there, we just need to be ready to pounce when they show up.
 
I have gave up on investing $$$$ in my 80 due to rust. In my case most of the rust is from internal leaks, plugged weep holes, dripping window seals, drain hose not in the draining ect. The front inner fenders are bad with rust too. If it wasn't that the rest of the 80 needing attention I would just find a donor body.

While pulling the front of the dash apart to fix trip meter, I am finding that the plastic is getting brittle and plug connectors are not separating like they use to. The locking clips of the electrical connectors break off easily too.

I restored a rusty FJ60 and it was not too hard. Restoring a rusty 80 would require a lot of cutting and welding, none of which I had to do to the FJ60. I pity anyone 10 to 20 years from now trying to do a restoration on an 80 with all the plastic clips and electronics.
 
i will start saving up, again I have a good drive train with locked axles, and i may be getting ahead of myself. gonna take it to a shop and get an idea on how bad it really is, I plan on lining it so If i can deal with the rust myself and spray over i will. option is a clean body on a good frame and swap engine, trans and axles?
 
Unless you do work yourself will likely cost quite a bit to get your powertrain in a new body and done right.
It's also a great time to change all oil seals and engine mounts and exhaust work, wrap harness at EGR, list goes on and on. Keep in mind you will have to Crack the A/C system. I would change any rubber easily accessible (hoses, motor mounts, belts)
 
i did my Hg last winter and all rubber on the engine was done and erg and harness, I have an ome lift on it but I'm due for new shocks, exhaust ans bushings. So if I'm doing that much it isn't that much further to swap axles and lift components. if I had a rig I had the old drive out of I could clean and re undercoat. and replace rear heater hose ( I actually use it) still not sure If I'm better sticking with what I know and I plan on waiting till it is warm and dry out to pull off the cladding, then I will really know what Im up against
 
I'd love to find a rust free 80 for an LS swap. Mine looks good, but rust underneath. I've actually thought of doing the swap anyway. I think I will age faster than it can rust at this stage of my life :)

My problem is it runs real good. 250K. First to second shift is not crisp, but maybe that is just normal. Not RPM raising, just not crisp. I Just want more power
 
I hear ya, mine runs great, although in need of some PM that I'm waiting on a bit better weather ( canadian rocky mountains) and it may be better to stay with what I know, although some ass hit my Kamar rear bumper in a parking lot the other day, almost totalled his ford truck and slightly bent the wing on my bumper!
 
I think I'll just do some PM, and if I want to go faster, I'll just floor it!. If it blows, then it gets an LS. It looks good just as it is, and it has all new springs and brakes, fixed the AC, remote start, etc. Gets 11-13 MPG. It has working lockers. The grandson takes it fishing in the Summer. I plow in the winter.


 
I think I'll just do some PM, and if I want to go faster, I'll just floor it!. If it blows, then it gets an LS. It looks good just as it is, and it has all new springs and brakes, fixed the AC, remote start, etc. Gets 11-13 MPG. It has working lockers. The grandson takes it fishing in the Summer. I plow in the winter.


Keep oil and water in it and you will never blow it. A buddy who had a shop years ago would collect engines throughout the year and in November he would have an engine blowing up party at his ranch. The Toyota engines would take silly amounts of punishment before they threw a rod. We removed the oil from one particular 22-R and it just seized after 3 minutes at wide open. Three hours later we started it up again but this time with out the water hose. It ran more than 2 minutes wide open and seized again but never tossed a rod. We put a 2 F to the same test and it sent a rod through the block into the bushes after several minutes. Good times!
 
Back
Top Bottom