Replace outside mirror glass?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 8, 2003
Threads
480
Messages
9,163
So I searched on this but could not find anyone describing the procedure for changing broken glass. I ask because there's a wrecked 80 near me an the mirror is intact but the housing is cracked. What should I be sure to get? Just the mirror and plastic frame the mirror is tightly encased in, or is there more to the story. Ideally, someone could tell me that I could simply rip the rest of the mirror off the truck and at home extract just the glass and its frame to transplant.

Thanks,

DougM
 
on my 92 i can pull the mirror and motor assembly by simply unscrewing one screw from the underside of the miror, then disconnecting the wiring. To remove the hole assembly you need to pull off the plastic cover on the inside and unscrew 3 or 4 screws, then disconnect the wiring. Let me know if there is an extra passenger side mirror because i need one.
Cheers.
 
I know this isn't what you're asking, but the glass appears to be held to the plastic piece that you actually remove from the housing by just some sort of sticky tape. I'm not sure if you could get a good mirror glass off the backing plate without breaking it.

It sounds like you're planning on replacing the mirror and backing as a unit. If just the glass is broken, you might check with Specter. I just ordered the glass by itself for $42. I still need to pull the backing to fix the jiggles, but hopefully, this will fix it.
 
You can remove the entire mirror from the inside door plastic triangle which holds the housing in place(3 screws from inside door) The plug to the entire housing runs into the door and can be removed as well. (pic 1)

By folding the breakaway mirror in- you can access the hidden screw on the side of the housing.(pic3)This allows the outer plastic to be removed when the 4 inner screws are removed.(pic2)
 
Last edited:
(pic3) This is the screw which holds the mirror assembly steady---if you have a jiggly mirror-this is the one that can stop the jiggles ***overtightening this screw is bad--and can result in stripping and cracking the plastic body of the mirrors inner housing**** If the mirror wont stop jiggling after repeated attempts to lightly tighten....use loctite--dont overtighten and break it****(dont ask how i know)

(pic1) lifting the mirror off the tabs which are easily broken if you try and yank out the mirror without lifting. If a tab is broken- typically you must remove the entire inner housing and replace the whole inner housing.

(pic2) are the inner 3 wires that must be disconnected from the mirrors inner housing.
View attachment 171485View attachment 171486View attachment 171487
 
Last edited:
(pic1) to access and remove the wiring--the plate can be popped and access to the wire is fairly easy by backing the wires out from the 3 spades back through the inner door arm pivot.(pic2)
View attachment 171488View attachment 171489
 
Last edited:
wire can be removed if changing the entire housing without unplugging from behind the door panel if necessary by backing out from the spades backward.
View attachment 171490
 
Last edited:
So I searched on this but could not find anyone describing the procedure for changing broken glass. I ask because there's a wrecked 80 near me an the mirror is intact but the housing is cracked. What should I be sure to get? Just the mirror and plastic frame the mirror is tightly encased in, or is there more to the story. Ideally, someone could tell me that I could simply rip the rest of the mirror off the truck and at home extract just the glass and its frame to transplant.

Thanks,

DougM

Hmm.. What color is it?

I might need to take a little trip.....
 
Bugs,

Unbelievable. Ask and you shall receive should be the motto here - sweet pictures and explanations!!

Dan,

It's a white one with grey interior and it rolled after a frontal hit so hard you can see the timing gears (ouch). They damaged pretty much every panel. I'm picking up the wheels and will take an inventory of other stuff - anything specific I should look at for ya?

DougM
 
Doug,

I am just after some bits and pieces, switches, door handle bezel, headrests, maybe a seat, seatbelt, antenna, and things like that. Nothing I really NEED, but a couple of "wouldn't mind havings"

I'll give you a call if I head up that way.
 
Back
Top Bottom