Recovering an open AC system

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

MDarius

I break stuff.
SILVER Star
Joined
Apr 10, 2006
Threads
176
Messages
2,058
Location
Bountiful, UT
Life is a little full and busy right now so I asked my 16 year-old son to take apart the front of the 97 so we can replace the radiator. "When you get to this point, come get me." He didn't come get me and he decided to disconnect the AC line at the AC cooler in front of the radiator. Is there a DIY way to recover this system, or do I have to take it in to a shop?
 
You will need to completely evacuate the system by putting it under vacuum prior to servicing with refrigerant. This will require special tooling.

Last year I replaced my entire AC system but left the servicing to a shop.
 
You probably could with the right tools and gauges, but at least around here a decent A/C shop isn't that expensive. If mine I would probably just have a shop do the A/C stuff.
 
Hijack:
Got a local recommendation for one?
Not sure if he is still around, but is great if still open. Works out of his home on Scenic Ave in CP. Pretty sure its Silva's, but has been 5yr + yrs since I have been there.
Silva's Auto Repair in Central Point , OR

He made some custom replacement lines and a/c refill for half if not more what it would cost at the dealer for my old BMW and ex-wifes Mazada.
 
Yes for sure take it to a shop to have the system evacuated. They can capture any refrigerant still in the system.

That is the only thing I use A/C shops for. I repair / replace my own stuff because it is so much cheaper. Then I re-charge with cheap cans of dust-off or equivalent.
 
Some parts stores have loaner vacuum pumps and gauges. Pretty easy watch. Few youtube videos. I've done it several over the years
 
Its not a hard process but you will need a set of manifold gauges a fairly decent compressor and a vacuum pump. I had the compressor, borrowed the gauges from autozone and bought the vacuum pump from harbor freight. Worked a charm when I had to swap out my expansion valve last year.
 
If the system was open to atmosphere, then you'll want to replace the receiver drier. You can get a Denso one under $20 from Amazon or Rockauto...simple bolt on affair.
 
+1 on the Harbor Freight electric vacuum pump and manifold gauges. I used that setup for when I replaced the compressor and receiver on my W124... For the FZJ80, you'll need 1.8-2 lbs of r134a and 10 cc of PAG-46 oil if you replace the receiver. You can get Dupont r134a in 1lb cans, without any sealant or additives, on Amazon.
 
+1 on the Harbor Freight electric vacuum pump and manifold gauges...

I used those to get the A/C on the '93 here in Louisiana working again.
My system didn't have any refrigerant pressure left due to a leak at an O-ring at the expansion valve. I found that one by pressurizing the system (90psi, Louisiana air...); vacuum didn't help with this one. Once I found the culprit (and cleaned the evap core in the process... and put fresh O-rings wherever I had touched the system), I installed a new drier, and just let the vacuum pump do its thing for a few hours before charging the system with fresh refrigerant.
 
If the system has been opened, then there is nothing left to recover.

When I replaced my ac system a couple years ago and priced a service at the shop, I ended up buying a vacuum pump and manifold gauges at harbor freight and a couple cans of refrigerant for less than the shop wanted and mine has been ice cold for years now.

Just use the the 20% coupons and also if they are already on sale you can get out for really cheap. Also check the reviews for the HF stuff, they have several models that look the same but some are duds.
 
Back
Top Bottom