Rebuilt Engine Woes

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

FineWynsFJ40

Too much to do...
Joined
Jan 13, 2005
Threads
84
Messages
1,377
Location
Grand Haven, MI
Ok, here's the setup: stock 1974 FJ40 completely rebuilt and restored body, with a (PO installed) GM Rochester 2-Jet carb w/ manual choke going into a freshly overhauled ~700 mile '74 F engine (rebuilt & bored 0.020" over) with headers, a no backpressure tractor muffler, and 2 1/2" exhaust.

Here is my dilemma: When choked it runs great, however, whenever I shut it off it diesels (ranging from none when it's fully warmed up to about 7-8 seconds) and then lets out a massive backfire out the tailpipe. When it doesn't diesel or backfire I smell excess gas. I have tried tweaking the carb, running lean and low RPM choked idle (weak) to normal to strong trying to get this to stop. It would seem that a freshly rebuilt engine would not have this problem, and it is really pissing me off since I'm at college now and don't really have the time to take it back to the place that did the engine for me and have them fix it. What do you think? Thanks in advance.

Brian
 
Check the "Anti-Idle" Solenoid - Make sure it gets power ("clicks" wehn the key comes on.

When you shut off the key, this thing is supposed to "de-energize" and shut off fuel to the carb.

Maybe that's what's happening.

Rocky
 
Check the "Anti-Idle" Solenoid - Make sure it gets power ("clicks" wehn the key comes on.

When you shut off the key, this thing is supposed to "de-energize" and shut off fuel to the carb.

Maybe that's what's happening.

Rocky


Does the Rochester 2BBL have an idle solenoid? Just curious.


And Finewyns...what is your idle speed? Too fast can cause dieseling, too.


Ed:confused:
 
Is there any warranty that comes with your rebuild? If so make them correct the problem.
 
Get rid of the Rochester and then report back. The motor is likely mechanically perfect. It's the supporting stuff like the carb, distributor and the like that goes bad. Get a carb built to run with that motor.
 
Starting with the first response: Rochester 2G carb doesn't have the anti-idle solenoid. I've got the idle around 650 or so, according to the F engine manual, Haynes, everybody on here and $OR, plus the little sticker that was under the hood with all the tune up info. This Friday I'll have time to bring it in and talk with them, but I wanted your opinions and suggestions first. The 2G carb ran great before the rebuild and before the motor started effing up, ran like a champ, and apparently that was what was the popular choice before Weber stole the market. I figured on too high of an idle or too much choke, but anything less and it hampers the performance of the engine in the colder weather we've been getting. Another 3 or 4 weeks and she'll be retired for the winter, as it is my personal vengeance against rust that she never see another winter ever again. Thanks for the ideas/suggestions, keep it up!!

Brian
 
If I read your first post correctly.....backfiring out the tailpipe is unburned fuel, so maybe the carb is fawked. Check the float level. I do not know anything about the R'Chester, but when you shut the engine off with the throttle closed, it will pull a lot of vacuum...so maybe something allowing the idle circuit to remain open? Just groping here. Run some SeaFoam through the tank with about 8 gallons or less fuel in the tank, or more SeaFoam if there is more fuel than 8 gal.
I agree with CruiserDrew that you should return to a stock setup, and I might just have one for you.;)

Are you cable or rod linkage? Guessing cable with a R'Chester?


Ed

EDIT: If you are in Michigan, there are a bunch of really cool guys there who might be able to he'p you.
 
I've literally removed every rochester that ever came on any 40 I ever bought, and immediately threw them away, the first day. When perfect, they're only mediocre, the other 99 per cent of the time they're junk. Worst carb I've ever tried to tune. Outdated, used up, and properly tossed out. Get yourself an oem carb and send it for rebuild to Jim C. If you're flooding the engine that badly, you can wash down the cylinder walls and your engine will be worthless.
 
Degnol, do you have a 1974 carb that you'd be willing to part with? It's a cable linkage, and you're all right, the thing isn't smooth like the Holley, Edelbrock, or stock carbs I've seen, this one has play in all the linkages. I'll SeaFoam it and see what happens, then report back. I'm just throwing out alternatives, but would an Edelbrock or Holley be a viable alternative to the stock carb? Not that I'm against OEM, I'm all for it, I'm just thinking availability and price, and it's the engineer in me to look for all possible options ;) Thanks guys!!

Edit: I am in MI, on the west coast, who here can help me? I talked with Hadley Industries a year or so ago, and he told me that I'd be wasting my money by returning to the stock setup. Of course, I was thinking fuel efficiency then, but not performance. I might be willing to part with a few greenbacks to get a carb that'll make my cruiser be all that it can be :grinpimp:
 
Last edited:
Get an AIsin (OEM) carb. There is none better. Have it rebuilt by someone reputable in the Land Cruiser community. It will be good for 20 years after that. Putting a crapped out, used up carb on a freshly rebuilt motor, seems wrong. I'll bet you'll be pleasantly suprised.
 
Degnol, do you have a 1974 carb that you'd be willing to part with? It's a cable linkage, and you're all right, the thing isn't smooth like the Holley, Edelbrock, or stock carbs I've seen, this one has play in all the linkages. I'll SeaFoam it and see what happens, then report back. I'm just throwing out alternatives, but would an Edelbrock or Holley be a viable alternative to the stock carb? Not that I'm against OEM, I'm all for it, I'm just thinking availability and price, and it's the engineer in me to look for all possible options ;) Thanks guys!!

Edit: I am in MI, on the west coast, who here can help me? I talked with Hadley Industries a year or so ago, and he told me that I'd be wasting my money by returning to the stock setup. Of course, I was thinking fuel efficiency then, but not performance. I might be willing to part with a few greenbacks to get a carb that'll make my cruiser be all that it can be :grinpimp:


I do have a '74 stock carb that I am running on my 40 right now. I rebuilt it about 6K ago with the help of PinHead and JimC. Runs just fine and would probably run just fine on yours, too. I just put in a new 2F and built another Aisan carb with ported vacuum advance for my new distributor. So, when I swap that in, I'll have the carb for sale. It will be set up for stock rod linkage. You can PM me if you want to talk about that.
I did meet at least three guys from Michigan, but I only remember one name.
Ron86Toy (Ron Fetter) is from Gladwin, MI. Don't know if that is close to you or not.
Yooper, on this board is from da UP, but might know guys in your area.

If I think of the other guys, I'll let you know. They both had 40s.

GL

Ed
 
I just filled up and put in 1 1/2 cans of SeaFoam so we'll see what that will do. I talked with the guys at CarQuest, and I think, since I rebuilt the carb, the throttle plates might not be closing all the way. Problem is, I don't have much time to screw around with it since I'm at college. Friday I have to go home so I'll have time & tools to pull it off and tinker. Tomco HAD Aisin carbs but as of last week have shut their doors:mad:, so I'm trying to find a source to get it, because for around $258 I can have a new 1974 Federal model Aisin carb... Grrr.... Anybody know where I can get one? Thanks again for all the help!
 
I have an OEM carb sitting on an F engine in my shop. When I swapped in the '86 2F, I used the carb with that engine. Fire me a PM if interested in it. It was the original carb with my "74.

Doug
 
I agree you need to replace that Rochester, but in the meantime check your ignition point gap. Won't cost you a dime and you'll eliminate a possibility. I had the same setup, and when mine did what you describe, I found the points were almost closed up.
 
I bought an freshly rebuilt OEM Aisan for my 1971 F engine from Mark Algazy of marksoffroad.net several years ago. It was a replacement for a Motorcraft 2BBL that came on the engine and drank fuel. It's still running great and I was able to reinstall the original air cleaner.

Leon...
 
Back
Top Bottom