Realtime Help: Broken bolt

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 16, 2004
Threads
23
Messages
509
Location
Behind the bar
We're installing lifts on three rigs today. We just snapped off the lower shock bolt on the rear axle. There's about 1/2 inch of shaft left with the head of the bolt.

Any suggestions as to how to get the rest of the bolt out?

I have a small torch (MAP gas), if that's appropriate, but no specialty broken-bolt-removal tools.
 
Whose trucks are you lifting?

Immerse in PB blaster.. again and again. Is enough bolt sticking out where you can file two flats then put a open end wrench or vice grips on it? If not then you need to drill it. take a punch and pop a divot as close to on center as possible, then start with a small drill bit and work your way up, until you just start kissing the internal screw threads of the sleeve the shock rests on. Then take a small pick and/or vice grip and hopefully the rest of the bolt will be free enough to work free and out of the hole. last thing is chase the threads with a tap.. I would resist the urge to try any form of "easy out," those typically make things worse, and you don't want to deal with a broken off easy-out in there.

:idea: oh and then you need a new bolt. hth..
 
Thanks! There's nothing sticking out to file or otherwise grip... we'll start the drill-out process once we get the fronts done.

Looks like a trip to Napa to get the correct tap and another bolt.

:beer:
 
Oh, yeah, goschbrandon and MomentRider are both going from stock to OME 2.5" Medium. :)
 
If you have a welder, you can take a nut and weld the nut on the inside to the remainder of the bolt.

Matthew
 
Welding stuck bolts usually works for me, but not in the way that you'd normally expect. Several times I've welded a head onto a bolt only to have it back out by hand afterwords. I'd try heat if you have room, and a left-handed drill bit if you have to go that far.

-Spike
 
It started pouring down rain shortly after we went out, so we wrapped up for the day. The bolt broke off quite a bit of the shaft and there's no way to get weld anything to it or grind it off.

We'll give a go at drilling it out in the morning. I'm hesitant to dry a left handed bit and heat, as if the bit breaks off in there, we'd have to do major surgery.

Brand new bits are already here. :) Tap and new bolt are in-process.

Thanks for the help, guys!
 
Good luck, if you end up breaking the extractor in there, you wont get it out. But then I guess you could just buy my 91 rear axle...:D

Here is some good info about extracting the bolt. Note the part where it breaks in the bolt shaft.... $!*# is right. http://www.asashop.org/autoinc/may2003/techtotech.htm


Matthew
 
We'll give a go at drilling it out in the morning. I'm hesitant to dry a left handed bit and heat, as if the bit breaks off in there, we'd have to do major surgery.

Why would you be hesitant to try a left-handed drill bit? It does the same thing as a right-handed drill bit, but spins the other direction. This has the benefit of possibly removing the broken bolt piece before you are forced to drill the whole thing out, rather than a normal drill bit that just forces the bolt farther in.

I would also suggest, if you were to try a left-handed drill bit, that you strike the end of the broken bolt a few times with a punch or drift and a hammer. This may loosen the threads, and the bolt could simply thread out.

-Spike
 
Why would you be hesitant to try a left-handed drill bit? It does the same thing as a right-handed drill bit, but spins the other direction. This has the benefit of possibly removing the broken bolt piece before you are forced to drill the whole thing out, rather than a normal drill bit that just forces the bolt farther in.

I would also suggest, if you were to try a left-handed drill bit, that you strike the end of the broken bolt a few times with a punch or drift and a hammer. This may loosen the threads, and the bolt could simply thread out.

-Spike

The article attached about extracting bolts also makes Spike's point....here is a cut and paste:

If you're very lucky, the heat and vibration of drilling will break the bond. This is why you want left-handed bits - if this works, you'll pull the piece out, rather than driving it further in.
 
If there is not enough bolt left to weld a nut on (its broken below flush)
I would take your new bolt, cut the head off, flip it 180 and weld it in the hole......a flat washer and a nylock nut to keep the shock on and your in business.

I fricken hate drilling bolts out, and if you can get them red hot:mad: they will almost always come out, welding a nut on works very well in a rust/seized situation, but when its aluminum and hardend steel with electrolisis (sp.) (the leg of a sterndrive or warn hubs) the reverse drill bit is my fave.
 
Why would you be hesitant to try a left-handed drill bit? It does the same thing as a right-handed drill bit, but spins the other direction. This has the benefit of possibly removing the broken bolt piece before you are forced to drill the whole thing out, rather than a normal drill bit that just forces the bolt farther in.

I would also suggest, if you were to try a left-handed drill bit, that you strike the end of the broken bolt a few times with a punch or drift and a hammer. This may loosen the threads, and the bolt could simply thread out.

-Spike

My synapse was a little gummed up last night... Thanks for reiterating. :)
 
No problem- just let us know what works. :D

-Spike
 
Couldn't find any left-handed bits or the correct pitch tap. We ended up drilling it out. Tried heat and extractors a bunch of times, and nothing would budge. We ordered a tap from McMaster yesterday that should show up sometime today.
 
We got it all drilled out on Sunday, and successfully tapped it last night. Didn't have to over-size it. :)

Thanks, all, for the help! :cheers:
 
:cheers:

-Spike
 
Back
Top Bottom