Real Time advice needed-OE Locking Diffs

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 12, 2007
Threads
90
Messages
2,104
Location
Gilbert, AZ
Bought my 94 LC last week. Fixed most of the interior gremlins and have now moved on to the underside.

I have the factory locking diffs. When I turn the dial to engage the rear and/or front diffs, the lights blink, but do not stay on. OK, no problem I thought, I will drive around a little in low range and see if maybe they are just stuck....nothing.

While R&Ring the dash, I added a CDL switch and did the 7-pin mod. Nothing there either! Did I miss something? I installed the CDL switch, disconnected the pin 7 wire, but nothing happens when I engage the switch. I do hear a relay type click, but no lights illuminate.

Any advice? I have a full shop and plenty of diagnostic equipment, so I could start pulling parts and checking the electrical system. However, if there is a common "quick-fix" that I am overlooking or didn't find in my thread search, please let me know. Thanks!!!
 
I'd check the locker actuators, there's a rebuild article in the FAQ. And, now that you've added the CDL switch, make sure you hit that when you go into low range, the f/r won't lock without the center locked first.
 
If the lockers (CDL and RR/FR) haven't been exercised in a loooong time they can be a real PITA to get to lock.

You mentioned driving around but my first suggestion would be to:

Find a nice big dirt area...

Put the rig in Low with the CDL button pushed (because of the Pin 7 mod). Check to see if the ABS and Ctr Diff icons light up (I'm assuming '94s have ABS?)

If no to the above, drive around...Tight turns, reverse, etc until you hear, see, feel the Ctr Diff lock. Try moving the Ctr Diff selector in and out of Low (leave the button pushed) numerous times (I think I read where one person did this 30 or more times before he was successful).

IF you get the Ctr Diff to lock proceed with the below - otherwise you have to get the CDL to work before you'll be able to get the RR/FR lockers to work (if they will)

Now, assuming you got the Ctr Diff to lock now try the rear locker. If it won't engage (light just keeps blinking) then try some slow tight turns, figure 8s, reversing, etc.

Repeat the above for the front lockers.


When I bought my '97 LX the Ctr Diff locked up pretty quick but the RR & FR lockers took some encouraging (tight turns etc). They are better now but still not to the point where I turn the dial and they lock immediately.

I've see a lot of threads where people kept at it for a long time of moving the selector, driving in tight turns, figure 8s, etc. for 30 mins or more and then finally voila! Success.

Hope that is what you experience otherwise getting the RR/FR lockers to work could get expensive, especially if you have to buy new actuators etc. to the tune of $800+ (from what I've heard)
 
Another possibility is that the CDL sensor is not working. If not, no other lockers will work. You have to get the CDL light on the dash to illuminate before the axle lockers will work.

-Spike
 
There are a couple of trouble-shooting steps for CDL not locking. I'm pretty sure they're covered in the FAQ, but here's the short version:

Once in the field per Corsair, in low, press the CDL button. You should be able to hear a faint click.

If you're getting the click, but no lock, try driving around for a while until it engages - likely cause is sticky actuator. When I had the problem, it took a week of locking it with the CDL button for short periods (minutes at a time) before it finally locked.

If you're getting lock, but no light, there is a sensor on the front top of the transfer case that needs help - some have luck beating it with a hammer (after removal), others (me included) simply replace it.

The Axle lockers won't engage until you get the CDL locking and the sensor lighting up the dash.
 
***Update***

Shorted out the t-case switch and that allowed me to engage the lockers and for the lights to come on...new switch ordered.

R&R'd front actuator. It was really clean inside, and moved with the power of a 9volt battery. Reinstalled the front actuator but DID NOT pay attention to the position of the gear when I removed it. Is this a big deal? I see some posts mention putting it back in the right orientation. Any advice?
 
Diff locks

Think outside the SQUARE!!!!!

You do NOT have to drive around in circles etc to check diff lock actuators Any of them.

JACK the front or rear of the truck up and put it on axle stands. Make sure that you chock the other wheels that are on the ground. Put the transmission into Neutral

Turn the ignition key to the ON position. DO NOT START THE MOTOR.

Engage the Center diff lock either by putting the Transfer Case into Low or hitting the CDL switch.

Roll under the truck and rotate the drive shaft attached to the jacked up axle until it locks. The CDL is now engaged!!!!

Climb out and then rotate one of the jacked up wheels while someone holds the other one. When the axle diff lock engages you will no longer be able to rotate the jacked up wheels.

This works better than farting around driving in circles.
While it is up there you can check the switches that indicate the locked status.

They get crap in them and stop conducting even though they are operated.

You can do this in the warmth of your garage with access to your manual and all your tools.

Cheers
 
Think outside the SQUARE!!!!!



You can do this in the air conditioned comfort of your garage with access to your manual and all your tools.

Cheers

Sarmajor

I corrected your Kiwi thinking so as to be appropriate for where I live...Phoenix:cool:

Turns out the problem was a bad t-case switch. Once replaced it made everything work again. Now my front diff won't release. I suppose that is an alignment issue caused by me when I removed the front actuator and cycled the locking pin a few times by hand. Nonetheless, I was able to complete a nice run with it this past weekend and even play tow truck a few times. That seemed to shut up the nay sayers who said my LC was too big and too low to do any serious trails. Both of the rigs I towed through a 4:banana: rated trail were Jeeps. Both had broken their driveshafts trying to navigate something I had already "crawled" through both forward and then backward to get them.
 
That's a great quote:

That seemed to shut up the nay sayers who said my LC was too big and too low to do any serious trails. Both of the rigs I towed through a 4:banana: rated trail were Jeeps. Both had broken their driveshafts trying to navigate something I had already "crawled" through both forward and then backward to get them.
 
Another possibility is that the CDL sensor is not working. If not, no other lockers will work. You have to get the CDL light on the dash to illuminate before the axle lockers will work.

-Spike

My thoughts too. I would also double-check that the correct wire was pulled during the 7-pin mod, and that it's not possibly grounding-out or touching another lead.

On edit: does the CDL light come on when you shift the T-Case into low?
 
there's a rebuild article in the FAQ.

I couldn't find it:confused: Could someone point me to it?

My rear won't engage and I've been meaning to look at it, but w/o the manual I was hoping for a good write up.
AJ
[Hijack off]
 
Back
Top Bottom