Quarter Panels - mounting - rivets?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 6, 2004
Threads
123
Messages
859
Location
Lodge Grass, Montana
I have two 3x3 rust spots on the back - having them cut out this week - planning on putting the black diamond plate to wrap the rear where the two holes will be - have any idea how they put the diamond plate on? Adhesive ? rivets? zip screws - :doh:

I like the ones from Specter - anyone ever use them?

The 40 is deep burgundy and I wonder if the stainless will look better -

Thought and comments appreciated... :beer:
 
the ones from specter are a rip off...very thin aluminum and way over priced...also, if you're rear fenders are uncut, they look stupid. go to your local scrap alum place and dig through their stock of scrap diamond plate until you find pieces large enough to make your own and cut with a grinder and cutoff wheel. i used carriage bolts to hold them on...the square underside will dig in the aluminum and not spin. also, put undercoating between the body panel and aluminum corner to keep moisture out. we did two 40's for $40 five years ago.
 
I am also very against diamond plate but not because of how it looks, I think it looks ok but, my father put diamond plate on my truck some years ago before I got my hands on it and it just destroyed the steel underneath it. They are a catalyst for rust IMO.

here is the link to my repair job for the rust diamond plate caused

just FYI but I say do it right instead of hide the inevitable
 
Ditto nutley. I can't tell you the number of 40's I pulled that shiznat off of only to find literally nearly nothing underneath. Buy a 200 buck welder at harbor freight and learn to use it, do it right!
 
Warrior products makes some smooth steel ones.
I've also thought about repairing my 2 spots and then bedlining that area to make them appear to have corner covers.
 
Nice work Bustanut - Interesting because I too don't weld - in this forum it is kinda like non-welders anon - "HI, my name is Jeff and I am a non-welder" - so thanks for the confidence builder!

Jeff
 
bustanutley said:
I am also very against diamond plate but not because of how it looks, I think it looks ok but, my father put diamond plate on my truck some years ago before I got my hands on it and it just destroyed the steel underneath it. They are a catalyst for rust IMO.
that's why i mentioned to put undercoating between the aluminum and the steel...keeps the moisture out.
 
The problems is not with the aluminum - it's with the electrolysis that occurs - use undercoating or tons of silicone and you should be cool - as stated twice now:D trucking and boating industries have placed aluminum on steel for decades - not rocket science, just takes prep work.

I bought a sheet of diamond pattern polished aluminum to skin my homemade tailgate and 1/4s - looks a little too thick, might be fun to wrestle it around the corners. Whole sheet was cheaper than 1 set of pre-fab.
 
I used stainless and "brushed it" is is very strong and makes up for the loss of material. I also painted the entire area when I did my body so there shouldn't be too much rust going on. They look sweet at night becuase of the way that the light shimmers on brushed stainless.

I used small stainless allenhead machine screws with nylock nuts on the back side. POP Rivets will always loosen over time. I have tried stainless and aluminum rivits on past jeeps and neither are up to the task. Real rivits maybe, but thats a lot of work. go with some type of bolt/nut combination so you can tghten them.

These are a little dirty, but they do look pretty sharp and different than anything else out there
 
Last edited:
I agree with the consensus to forget about "patching" steel with aluminum - although it's tempting because of economy and ease, it's just asking for more trouble and very difficult to get a satisfory results in terms of looks.

Nutley's work is inspiring, especially to those of us who haven't welded before - very nice job completed in what seemed like no time at all.

And Jetboy's work is encouraging because he used fasteners in lieu of welding and apparently got good results. Guess it all depends on whether like the look of plating or not.
 
"And Jetboy's work is encouraging because he used fasteners in lieu of welding and apparently got good results. Guess it all depends on whether like the look of plating or not."

I think that the stock look is desireable. I just don't have the skills to do the smothing and body work to fix the rust that was on mine. I used stainless because I had it sitting arround from a past project and it was easy to use. The advantage of the stainless is the strength. (the piced I used was pretty thick, but I can't remember the guage)
 
Back
Top Bottom