Power steering

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 12, 2018
Threads
30
Messages
155
Location
Calgary
Hi guys

My power steering decided to stop working this morning ( I haven't checked fluid or anything as I was on my way to work and it was dark, I'll check the fluid level at break time! )
So I noticed that when I turn I can hear the pump!! Hopefully it's just a hose but anyone have sudden power steering loss and have any good info before I start pulling the pump off?

Thanks
 
Probably a loss of fluid through a cracked hose. If fluid is dry then its leaking somewhere
 
I'm hoping it's just a hose, I'll look on break when its light.
Holy s*** is the steering heavy with no power assist lol
 
If you didnt hear the pump groaning over the last few days then i would say one of the lines decided to give out. I had this happen back in 2015 on a trail and it wasnt fun. However, I was able to get a new line and fluid and the pump was perfectly fine after that.
 
If you didnt hear the pump groaning over the last few days then i would say one of the lines decided to give out. I had this happen back in 2015 on a trail and it wasnt fun. However, I was able to get a new line and fluid and the pump was perfectly fine after that.

Well this is the road I turned around this morning which looks more than likely a hose let go!

( thank god)
Will check at break time just to confirm

IMG-20191009-WA0001.webp


IMG-20191009-WA0002.webp
 
Blyme! Looks like a crime scene. lol Yeah a hose (or two) is shot. There are (at least) 3 to blame, but it's either your high pressure hose or one of the return lines. Absolutewitsend.com (among others) carries a 3 hose set to address.
 
Ah yeah, if it went out when you were making that 3-point turn then i would say hose. My hose also let go while making a sharp turn up a very tight switchback on a trail...so yeah sounds like the line couldnt hold up any longer when you cranked the wheel. I think a new hose and a quart of atf will get you sorted out.
 

It’s usually the low pressure hose that just degrades so badly that the ends split and cause the leaking. High pressure hose leaks cause a huge mess but they tend to last a very very long time.
 
Blyme! Looks like a crime scene. lol Yeah a hose (or two) is shot. There are (at least) 3 to blame, but it's either your high pressure hose or one of the return lines. Absolutewitsend.com (among others) carries a 3 hose set to address.
Thanks!!
 
Don;t drive it with all the fluid leaking out or you will smoke the pump!
 
Its pouring out the back of the pump!
New pump or would I get away with a seal kit ?
 
Its pouring out the back of the pump!
New pump or would I get away with a seal kit ?
Nope!

You blew out the little plug in there!

Look around on the drive and the road for a plug with an oring on it, the back is sort of C-shaped

You will have to clean it, shove it back in, and fill the hole with "The Right Stuff" spray can sealant to keep it in there.

There are no replacement kits or repair kits for that.

You may be able to sing the inside of the opening after inserting it to prevent it from popping out again.
 
Nope!

You blew out the little plug in there!

Look around on the drive and the road for a plug with an oring on it, the back is sort of C-shaped

You will have to clean it, shove it back in, and fill the hole with "The Right Stuff" spray can sealant to keep it in there.

There are no replacement kits or repair kits for that.

You may be able to sing the inside of the opening after inserting it to prevent it from popping out again.
The plug is about 1/2" in diameter and about 3/4" long.
 
I had the same thing happen on a reman non-OEM pump, the non-serviceable plug on the back blows out and it's a big hole, it will drain as fast as you can fill it. I replaced the pump with a Toyota OEM pump, and I recommend you do the same. In the meantime, you can bandaid it with a rubber cork and backing it up with JB weld putty, then refill and bleed the system. I did the same in an O'Reilly's on the side of the highway and made it home 2 hours just fine.

Here's the procedure:

And not to toot my own horn but I did this 3 times so I made a video companion :)
 
What about if the plug can't be found!?
Thanks

If thats indeed what happened then you will find something that looks like a small freeze plug close by the spill. Reuse it by tapping it in. If you can't find it then use whatever: a stick, a wine cork, JB Weld, etc. Its just gravity feed at that point so very low pressure. Then plan to get a new pump.
 
Last edited:
Is this it ?
I'm planning on doing an ls swap next year,
If I do a bodge job will it last long enough before I rip the 1fze out without fluffing anything else up? Like the steering box!

IMG-20191009-WA0003.webp
 
Is this it ?
I'm planning on doing an ls swap next year,
If I do a bodge job will it last long enough before I rip the 1fze out without fluffing anything else up? Like the steering box!

View attachment 2103234
Is this it ?
I'm planning on doing an ls swap next year,
If I do a bodge job will it last long enough before I rip the 1fze out without fluffing anything else up? Like the steering box!

View attachment 2103234

if you wind up getting a new pump I’d love to get that plug from you.
 
Back
Top Bottom