PHH bi-pass

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 14, 2008
Threads
34
Messages
302
Location
Alton, IL (near St Louis, MO)
I am going to change the phh this weekend and I'm still on the fence about doing the bi-pass or keep it stock. I have read many threads regarding the phh and there is a wealth of info out there that is totally appreciated by this hombre. I see that the large majority keeps it stock and does not do the bi-pass. Has there been any faliures due to the bi-pass? Just want opinions as these old eyes are tired of reading.
 
Don't know about any failures, but ...

At the Houston Cruisers Club tech session I was at the guy leading the charge would not do anything but a PHH ectotomy ! :D

He used a silicone hose w/ a regular over it as a wear preventer in lieu of the bottom portion of the metal pipe , and secured both ends with constant tension clapms.

I still need to do mine, and may attempt a "normal" :p repair before doing the ectotomy.

Maybe.

Sears makes a killer tool, BTW, for getting on that spring hose clamp of the PHH - the one closest to the engine.

00971007000


Hopefully others here will chime in w/ their .02's.

Good Luck !

Britt
 
I am completing a HG PM and have removed the rear heater and the supply lines. This is an enclosed loop purely designed to provide additional heat to the rear of the cab. The standard heater is more then enough to heat the interior. I removed my based on possible failure (rust) and risk damaging the engine.

Van
 
At the Houston Cruisers Club tech session I was at the guy leading the charge would not do anything but a PHH ectotomy ! :D

He used a silicone hose w/ a regular over it as a wear preventer in lieu of the bottom portion of the metal pipe , and secured both ends with constant tension clapms.

I still need to do mine, and may attempt a "normal" :p repair before doing the ectotomy.

Maybe.

Sears makes a killer tool, BTW, for getting on that spring hose clamp of the PHH - the one closest to the engine.

00971007000


Hopefully others here will chime in w/ their .02's.

Good Luck !

Britt

00947390000

Craftsman Cable Operated Hose Clamp Pliers - Model 28650-998 at Sears.com

$39

search results:
Sears.com
 
I bypassed mine about 6 months ago, I havn't had any problems. I went to John Deere and got a piece of heavy duty heater hose to use for the bypass.
 
can you please explain this by-pass? if I never wanted to use the rear heater again what would I do?
 
I bypassed mine about 6 months ago, I havn't had any problems. I went to John Deere and got a piece of heavy duty heater hose to use for the bypass.

From what I've read so far you need 18" of hose for the bi-pass, is that what you found when you did yours? I ordered 24" of silicone heater/coolant hose as well as the constant tension clamps from McMaster Carr (can't remember who 1st found this a few years ago but thanks). You have to order the hose (the heavy duty) in 1 ft increments. Ordered yesterday got it today.
 
PHH bypass? does this bypass the PHH or is this separate from it and a bypass/delete for the rear heater?
 
then what do you do? does anyone have a picture of what you are doing?
 
The "PHH Bypass" and the rear heater bypass are 2 completely different issues. The "PHH Bypass" is not actually a "Bypass" & applies only to the 1FZ engines ('93-97). It is really a longer piece of sleeved or otherwise protected heater hose that replaces the PHH and the metal tube above it. Then when this section of heater hose needs replacement you don't have the particularly nasty PHH replacement chore.

Now the rear heater bypass is an actual bypass of that system. You can at your option leave the majority of the existing hardware in place. In a nut shell, you remove the 'T's, in the heater hose system, that split the front and rear heater systems and connect only the front heater system.

ExpeditionLCMajorcoolingoverhaul

The above link is on a website of a MUD member that has an excellent "work in progress" expediton build going with his 80. It is one of the best resources that I've seen for the cooling system & has an excellent diagram for heater hoses that's not even in the FSM.

You can also do a search on MUD for PHH & rear heater threads that are very helpful. HTH!
 
You can also do a search on MUD for PHH & rear heater threads that are very helpful. HTH!

been doing just that, going to do the PHH-ectomy soon, keeping the rear heat, functions as a dual zone heater for my kids and allows me to roll in luke-warm room temp like I like.:steer:

-aside Q? what do HTH stand for?
 
aaaahaa, I see, thanks for that.
 
I have has the "phh ectomie" on my rig for 3 years and 50k miles now with no issues whatsoever. It is nothing more than connecting the heater hose from the block directly to the heater valve. I have gates green stripe sleeved inside of a larger gates green stripe to protect in case of any abrasion. If you did this with a true silicon hose, you would never have to worry about it again.

Buck
 
Buckru, can you show some pics of what you did? I want to by-pass the rear heat all together
 
What I can't understand is why you would bypass. Assuming you get good hose (I used Silicone), you should never have to do it again. Laziness? The stock configuration is just fine after the PHH has been replaced, I don't see the advantage of the bypass, and indeed it would add more clutter to a very packed area.

There are no shortcomings to the steel section, that I can figure, except that people have just developed a hatred toward the configuration and absolutely MUST SEEK REVENGE by removing it.
Kind of like killing an Ex wife right after she remarries and the alimony payments have ended - What's the point?

In my post:
https://forum.ih8mud.com/80-series-tech/259343-thoughts-after-my-first-phh-job-pic.html
I found that installing the new Silicone PHH was easy and took mere minutes. The removal of the F:censor:ing clamp was the tough part.
That Sears wrench would have saved me 1 1/2 hours, had I known.:mad:
 
REVENGE was so great in throwing that peice of metal across the road once I tore it off.:D

Ok yes part lazy, and I tried to keep it the factory config but hoenstly my :wrench: is not that great and ended up just pissing me off.

I am pleased and comfortable with my desicion to run the by-pass method.

You are right (like everyone else) that the most difficult part is the removal of the old hose and clamp. I literally had to scrape the plastic from the metal.
 
It was patience for me... just ran out of it so performed the ectomy. maybe at a later date I can redo my hoses with something better than rubber and more abrasion resistant than Silicone. (copper or stainless braided line)
 
Back
Top Bottom