Part Time ? again

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 25, 2008
Threads
172
Messages
1,666
Location
Opelika, AL
I know there was a thread started not long ago about the part-time kit from slee but the answers were hard for a novice like me to comprehend.

1). Loose ABS in front when hubs are unlocked but what about when CDL switch is on with hubs unlocked?
2). If you put an automatic locker like the Aussie in the front will it engage with hubs unlocked and CDL engaged? Would this interfer with the steering like it does before part-time kit? That might not even be possibe but I'm asking cause I don't fully understand.

If anyone can think of any reason that I shouldn't or should get this kit living in Alabama where we do tend to get a good bit of rain at times. Although I've had plenty of experience with 2wd's and some part-time 4wd and did fine in this weather. Please let me know. Based on what I've read on MUD I've decided against a lift at this time and going to deal with gearing, lockers, DS's, axles, basically whole drivetrain before I do a lift. This is just one more piece to consider.


REMEMBER I KNOW NOTHING
 
2). If you put an automatic locker like the Aussie in the front will it engage with hubs unlocked and CDL engaged? Would this interfer with the steering like it does before part-time kit?

IIRC all automatic lockers are always locked .. they only allow one tire spin faster then the other ( never slow ) so at the end you will be locked on front always .. it means always your front inners still runing .. with or without your CDL activated ..

The auto locker does nothing with the steering coz .. for the steering with your hubs UN locked .. it's still like nothing diferent there ..
 
Can someone complete my equations keeping in mine this is with a PART-TIME Kit installed? I think this type of equation would help me to understand what is going on with the 3 variables.

CDL off + HUBS unlocked = What effect on Aussie and steering?
CDL on + HUBS unlocked = What effect on Aussie and steering?
CDL on + HUBS locked = What effect on Aussie and steering?
 
With the hubs unlocked you won't notice an auto locker up front. Do you already have one installed? I highly recommend against a front auto locker.
 
With the hubs unlocked you won't notice an auto locker up front. Do you already have one installed? I highly recommend against a front auto locker.
x100...no auto lockers in front...only in rear
 
Can someone complete my equations keeping in mine this is with a PART-TIME Kit installed? I think this type of equation would help me to understand what is going on with the 3 variables.

CDL off + HUBS unlocked = What effect on Aussie and steering?
CDL on + HUBS unlocked = What effect on Aussie and steering?
CDL on + HUBS locked = What effect on Aussie and steering?

I have an Aussie locker in the front of a mini truck, I can't feel it from the steering when the front hubs are locked. Aussie Locker doesn't lock ALL the time. The following texts are from Aussie Lockers

Unlike manual lockers which do not provide differential action when locked and severely hamper steering and directional maneuverability, the "Aussie Locker®’s" smooth and sensitive operation allows differential action resulting in uncompromised steering, uphill or down, soft or hard surfaces. Even on highway driving the "Aussie Locker"® does not impede performance.​
The Aussie Locker relies on a simple and highly innovative mechanical design which makes use of two distinct sets of forces, "ground driven" forces acting on a wheel when cornering (forces the outside of the wheel to turn faster) and the engine driven forces through the drivetrain. The combination of these two sets of opposing forces and the unique Aussie Locker design allow the automatic locking an unlocking of the driving gears when a vehicle turns or requires differential action. ​
 
IF his DT is DISCONNECTED then he can do anything he wants:mad:


Manual hubs will d/c it from the DT!

I cant believe you think it will affect anything disconnected?

What!:mad:

Put the hubs in Unlock, they part no longer part of the DT, What!:mad:

ooooh, what if you welded the front diff!

welded, then UNlocked the hubs?, what!

What is so hard to understand?

I once drove a welded diff in the back of my truck from the salvage yard I pulled it from to my house, about 100miles , the under steer was excruciating!:mad:
 
Last edited:
I cant believe you think it will affect anything disconnected?

What!:mad:

Put the hubs in Unlock, they part no longer part of the DT, What!:mad:

ooooh, what if you welded the front diff!

welded, then UNlocked the hubs?, what!

What is so hard to understand?


Don't get your panties in a bunch

I'm thinking that if the hubs were unlocked that they were not going to interfer with the steering but I didn't know for sure that's why I asked. I like to know for sure about things before I jump in and spend over $500 for something. Arrogant responses like this don't do anybody any good. In the future if you don't like the question then don't respond.

:ban:
 
IF his DT is DISCONNECTED then he can do anything he wants:mad:


Manual hubs will d/c it from the DT!

I cant believe you think it will affect anything disconnected?

What!:mad:

Put the hubs in Unlock, they part no longer part of the DT, What!:mad:

ooooh, what if you welded the front diff!

welded, then UNlocked the hubs?, what!

What is so hard to understand?

I once drove a welded diff in the back of my truck from the salvage yard I pulled it from to my house, about 100miles , the under steer was excruciating!:mad:


welcome to pirate.... er mud.
 
There have a been a few 80 owners that have gotten locking hubs and just dropped their Front DS to have a parttime 4x4 rig.
If you decide to try an autolocker up front then I will be the first to want to know how it performs, and if it sucks, pull it and sell it. If it's nice, keep it and help me install mine!
 
aisin if you can get them at a good price. I am told that solid axled mini truck hubs work, don't hold me to that.
Don't know anything about the AVM
 
I just read the Aisin thing at Front Range Off-road. I'll probably just go with the AVM's since Cristo offers it in the kit. With that said I might want to make sure Cristo has this kit in stock because I don't see the installation instructions anymore. I could have swore that I saw it there a month ago.
 
I used to run an auto locker up front with my solid front axle Toyota mini-truck and I absolutely hated it.

With the T-case in 2WD and the hubs unlocked, the locker was completely unnoticable and the steering was perfectly fine. But once the T-case was in 4WD and the hubs locked, the steering was horrendous, unpredictable, slow and it was generally all around dangerous to drive, except for at slow speeds off road. I later switched to an ARB air locker up front.

With my FJZ80, I'm only locked in the rear axle as of now, but if/when I ever lock the front, it will be ARB only or nothing.

As for hubs, Aisin, which is the OEM manufacture for Toyota are best hubs out there. Probably the easiest source is wrecking yards from 1979-1985 Toyota trucks and 4runners. Maybe early Land Cruisers. Don't get the hubs off of IFS trucks and 4Runners or early Tacomas as they won't fit. Some folks sell them new, but they are very expensive.

I personally would not waste my time with a part time conversion. The only reason I can think of to do it would be less wear and tear on the front end and possibly increased gas mileage. It looks like the increase gas mileage would be negligable at best from what I hear and whatever money it would cost to you do the conversion, you'd be better off investing in rebuilding your front axle anyway.

On the other hand, having full time 4WD has a lot of safety advantages, even on the highway. For one, you're less likely to oversteer around a corner. And after having used hubs for years and having to get out in the mud and rain to lock them, there's a lot to be said, about doing nothing more than pushing a button and moving a shifter.

Just my opinion. Good luck.

Edit: All that said, I just read this thread that puts to question the whole gas mileage thing:

https://forum.ih8mud.com/80-series-tech/208887-1991-80-wagon-vc-disconnect.html
 
I tend to like part time 4wd mainly because i rather wear the front end on the trail and not on the road.
That been said i also think that the part time kit for the 80 is too big of an expense and i would rather spend my money elsewhere, like for example getting an air locker instead of an auto locker.
If you do go with part time the Aisin hubs are superior to the AVMs but they will not fit without some modifications.
I also think that one of the best mods you can do to your truck is an aftermarket suspension, it will handle better and, depending on the terrain, will perform better offroad than a stock truck with lockers.
When you're dragging your belly all the time even a locked truck has a hard time moving.
 
One thing about running with the hubs unlocked but the cdl on, is that you will wear out the bushing on any locking hub. It is not really designed to run with the hubs unlocked and the drive line turning. You will still be turning all the stuff in front as well. Asians are really strong and cheap. As I have stated before, it may be better for you to buy some Asians and install them, drop the front drive line and see if you like the way it handles first. Then if you like the way it handles, pursue the part time kit. Good luck, robbie.
 
I used to run an auto locker up front with my solid front axle Toyota mini-truck and I absolutely hated it.

With the T-case in 2WD and the hubs unlocked, the locker was completely unnoticable and the steering was perfectly fine. But once the T-case was in 4WD and the hubs locked, the steering was horrendous, unpredictable, slow and it was generally all around dangerous to drive, except for at slow speeds off road. I later switched to an ARB air locker up front.



Because it was a spool?.....nahh, yer joking right?


(spool on a STEER axle, who'da thunk it?)



One thing about running with the hubs unlocked but the cdl on, is that you will wear out the bushing on any locking hub. It is not really designed to run with the hubs unlocked and the drive line turning. You will still be turning all the stuff in front as well. Asians are really strong and cheap. As I have stated before, it may be better for you to buy some Asians and install them, drop the front drive line and see if you like the way it handles first. Then if you like the way it handles, pursue the part time kit. Good luck, robbie.



isn't there a quick disconnect for drive shafts? :hhmm:

all you would need is a holder (summit has DS holders, mandatory for drag cars;) ) as the hubs would inhibit the pumpkin from turning and and spinning the shaft.


Before I bought a conversion and PERMANENTLY LOST awd ability. I would install hubs, make friends with two 14mm wrench's and OMG!!! 4 bolts!! :eek: aggghh!


Summer: d/c shaft, PT CDL locked, NO ABS Need 4WD? crawl under!(5minutes?)
Fall: connect shaft, hubs in or out, 2WD/ AWD/ 4WD ABS? YES
Winter: hubs locked AWD/ 4WD ABS? YES

How much did I just save you?, er, I mean how much is a conversion kit?

In no way does it make sense to me to disable any part of the 80's DT, it IMHO is easier to drop a shaft by 100fold than to remove PERMANENTLY its AWD function and ABS. (install PT kit?...4 hours...:hhmm: let me think about that one.. :doh:)

But then again, I'm thinking 3fe(no abs) and how hard it is for me to drop a shaft:rolleyes: Poor poor us :frown: how do we live with no ABS :crybaby: boo hoo trying to live with that and labor of removing a shaft and installing hubs. (yawn) :rolleyes:

Oh yeah, and no VC either :flipoff2:
 
Last edited:
Anybody using Aisin hubs that tell me if they are worth it and where I can get them?

I thought you can order 'em from Dan coz here are a factory option .. ( expensive sure .. ) or buy a set from Marlin ( not cheap also ) sure they share the sabe external config, just wonder if the inner diameter it's compatible with ABS bierfields that use upper there ..
 
Before I bought a conversion and PERMANENTLY LOST awd ability. I would install hubs, make friends with two 14mm wrench's and OMG!!! 4 bolts!! :eek: aggghh!
kit?

I agree that installing hubs and dropping the front drive shaft would be a good, cheap way to test whether or not you liked the feel of the part time 4wd. But as a long term solution it seems like a lot of trouble.
 
Back
Top Bottom