oil pressure ?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 6, 2004
Threads
234
Messages
4,449
Location
Bozeman, MT
Well I searched but I kept getting like 250 pages of results so I just figured this would be faster. I was wondering what the standard oil pressure for an F should be? Mine was running at like 30 psi and when I would accel and stuff it would jump up as high as 100 psi. Seemed awfully high to me. I actually broke the needle on my first oil pressure gauge. One thought was that the oil might be thick and cause more pressure. I also noticed that after a few minutes it dropped to about 20 psi sitting at idle. So once it heated up it had thinned out and dropped the pressure some. So I was just wondering what the standard pressure should be. Does the f just run kind of high or do I need to use a lighter weight oil or what.
 
Don't know if there is standard oil pressure...20 PSI warm idle sounds good though.
But 100 PSI? Check your oil pressure relief valve (external on earlier Fs).
 
From the F engine manual, oil pump delivery is >16 liters per minute at 1000 rpm of pump at 122-140 degrees F at 1 kg/cm2 (14.2 psi).
 
Ok so I'm sitting at 20 psi after it warms up which isnt to bad, but any ideas on what it should be when your at like 2500 or 3000 rpms trying to accel up a hill. thats when it hits the big #'s and makes me wonder.
 
I think Pighead got it. The oil pressure regulator safety valve is supposed to operate between 44 and 50 PSI at an engine speed of 2400 RPM. It sounds like yours is either not operating at all (clogged), or is adjusted too tight. You turn the adjusting bolt on the end counterclockwise to reduce the spring pressure.
 
Mine reads 45 PSI running down a freeway at 2700 RPM...isn't the pressure relief valve supposed to open at 60 or 70?
 
IDave said:
The oil pressure regulator safety valve is supposed to operate between 44 and 50 PSI at an engine speed of 2400 RPM. It sounds like yours is either not operating at all (clogged), or is adjusted too tight. You turn the adjusting bolt on the end counterclockwise to reduce the spring pressure.


Wheres it at exactly? I didnt even know there was one. Maybe someone could toss up a pic so I dont spend a while looking.
 
Driver's side of the engine block, down low. horizontally mounted cylinder shaped gizmo..
 
Kinda looks like a jet plane. Or something. Adjustment nut at the front. Right about in the middle of this view. :D
Fengine (Small).webp
 
The first gauge went to 100 and the needle went around past 100 and then broke. This one is much better quality gauge also to 100 and it seems to work just fine. sits when I'm idling moves up with the rpms I don't think its the gauge. As for the regulator I have an early f and it is facing the opposite way as in the diagram. Is it on backwards or did it change. Either way it seems to be tightened all the way in so I'll loosen it up and see if that helps.
 
clemson55 said:
I have an early f and it is facing the opposite way as in the diagram. Is it on backwards or did it change.


This figure is from the 1964 manual, F135 engine, and shows the regulator oriented the same as the later Fs (I have one of each, 135, 145, 155). The design didn't change. Your's is on backwards. :eek: :doh: :frown: :crybaby: :o
foil (Small).webp
 
I believe Mr. Whatley used an F external regulator as part of his 2F oiling improvements...Think he said there were two varieties of regulators. Think there was some how-to regarding setting pressure in the regulator too.
 
IDave said:
This figure is from the 1964 manual, F135 engine, and shows the regulator oriented the same as the later Fs (I have one of each, 135, 145, 155). The design didn't change. Your's is on backwards. :eek: :doh: :frown: :crybaby: :o


Guess I need to turn it around then. That how it was always on there and I didn't know what it was so I just left it. Not I know so I guess I better fix it.
 
Might save your engine! :)
 
Consider yourself EXTREMELY lucky that you haven't lunched anything!


Years ago a machine shop delivered an engine to me with the regulator installed backwards. At the time, I had a few different guys hanging around the shop helping me with some of the 'grunt' labor. The guy that was there at the time installed the filter hoses without ever realizing that the regulator was on backwards.

In less than a minute after start up, the front oil galley plug shot out of the block and right into a brand new 4 core radiator! :eek:

When I discovered the problem, I called the machine shop and told them that they would be buying my customer a new radiator. They said 'Why, this one could be patched."

My answer: "Yes, it could. But that's not what my customer paid for."

They bought a new radiator.;)

Again.....consider yourself VERY LUCKY.
 
Oil pressure - 2F

I rebuilt my 2F - all new bearings.
Hot engine with 20w-50 idles at 52 psi and hits just under 60 psi running down the highway.
It maxes out at 67 psi - cold start. Cold start here in Saudi Arabia is not very cold - never below 50 deg F.
 
Back
Top Bottom