The joys of horse ownership...
Official 200 Series Chat and BS Thread
- Thread starter MScruiser
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
Road trip info - 268 miles today at 75mph constant.
Running 35's = 3/4 tank of gas used....not bad at all. The tire noise was drowned out by WuTang and Black keys.
Running 35's = 3/4 tank of gas used....not bad at all. The tire noise was drowned out by WuTang and Black keys.
- Thread starter
- #143
Does anyone know the bulb types for the tail lights, brake lights, and reverse lights?
- Thread starter
- #144
Your horse sounds like an A-hole.
Hahaha she's a moody mare, females.. Doesn't matter what the species watch out when it's that time of the month.
There was a thread a while back regardind swapping out bulbs to leds, I'll check my manual
- Thread starter
- #146
Anyone?
My reverse lights SUCK!!
I really want to replace them with the brightest LEDs I can find. K rating be damned!
- Thread starter
- #147
Anybody looking for an Amazon Green 200?
http://www.cars.com/vehicledetail/detail/630259750/overview/
http://www.cars.com/vehicledetail/detail/630259750/overview/
it appears to be the same vehicle
After this next snow storm hits within the next 48 hours we should post up in the picture thread of our rigs flexing out on snow plow banks.
and if you don't I will.
and if you don't I will.
strange - it worked this time
- Thread starter
- #153
Has anyone tried replacing their tail lights / reverse lights with LEDs?
I HATE my reverse lights and I think I have the bulb type figured out from talking to Beno.
I replaced my lights on my FJ40, but it required load resistors to get them to work properly. Those things gave me a serious 2nd degree burn one time (I actually heard my finger sizzling, like bacon hitting a hot frying pan). I am hoping to not deal with those again.
Anyways, was just seeing/hoping I could find out if LED bulbs were plug and play like they are on many vehicles, or if they require the load resistors.
I HATE my reverse lights and I think I have the bulb type figured out from talking to Beno.
I replaced my lights on my FJ40, but it required load resistors to get them to work properly. Those things gave me a serious 2nd degree burn one time (I actually heard my finger sizzling, like bacon hitting a hot frying pan). I am hoping to not deal with those again.
Anyways, was just seeing/hoping I could find out if LED bulbs were plug and play like they are on many vehicles, or if they require the load resistors.
I tried LEDs as back up and rear plate lights on my 4Runner. Aside from failing my annual VA state inspection for having non-DOT approved bulbs, the back up lights didn't throw any more light than the stock bulbs, they were only whiter. Didn't give me bacon fingers though, so there's that...
- Thread starter
- #155
Good to hear. Yeah, as to how much throw a bulb has, it all has to do with the number of bulbs vs. the claimed wattage (or so I have found). The companies like to advertise that they have a 10 watt bulb, when in reality, they have multiple low powered bulbs.
I have found that the new q3 or q5 Cree Based bulbs with a large projector bulb should actually give more throw, but there's where the question comes into play: will the large, high watt cree boards require a load resistor?
I have found that the new q3 or q5 Cree Based bulbs with a large projector bulb should actually give more throw, but there's where the question comes into play: will the large, high watt cree boards require a load resistor?
Haven't used them but people on here have ordered from them before.
https://www.superbrightleds.com
Brake/tail lights aren't showing up for me but I'm sure once you know the "bulb type" it'll be easy to get the appropriate replacement. I think these shoild all be plug and play except the turn bulbs would need resistors to stop the fast flashing.
https://www.superbrightleds.com
Brake/tail lights aren't showing up for me but I'm sure once you know the "bulb type" it'll be easy to get the appropriate replacement. I think these shoild all be plug and play except the turn bulbs would need resistors to stop the fast flashing.
- Thread starter
- #158
I used that same company when I bought my fj40 bulbs.
I just want to make sure that the 200 Series' computer could handle the draw of the high watt cree bulbs.
I just want to make sure that the 200 Series' computer could handle the draw of the high watt cree bulbs.
No - sorry
I saved the images to my desktop at home though. When I get home from work I'll see if there's a link attached. I found them surfing Google images. I'll let you know what I find or not find.
thanks
Looks like the approach angle might be a little bit better than stock with that front bumper... Might be easier to get a tire on an obstacle with that bumper compared to stock.