No Start Issue, Steps So Far

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 4, 2018
Threads
59
Messages
269
Location
Marietta, GA
I have been working slowly for a couple of months to get my 40 on the road and am trying to get it started for the first time since I got my rebuilt carb back from Mark. When I turn the key, I get nothing at all. Observation and steps taken so far include...
- Charged battery - currently at 12.5V when measured between the posts. All lights work
- Tested chassis ground to battery, 12.4v
- Tested Battery + to starter, 12.4v
- Tested ground from starter to chassis, 12.4v
- whacked the starter a couple times with a hammer
- I hooked my multimeter up to the B/W wire that goes to the starter solenoid and turned the the key to 'start'. I videotaped the results on my meter (see link). Does this look strange?



Thanks - Farrell
 
Will it crank,engage,click, if you use a jumper wire to the terminal the black/white wire is on? If it does, maybe power isn’t getting to the ignition switch. Or the contacts in the switch are worn out ( poor connection).
 
It will crank using a jumper wire. I will pull out the switch and check it as well as the wore run to the starter. Thanks
 
The 1971 will not have a fused starter circuit. Check the key switch is actually plugged in to the harness. It is possible to plug the 4 pin connector in BACKWARDS!!! Check that the Black/Red wire is on the AM terminal of the key switch when the connector is plugged in. Check it again...

If it is plugged in correctly, pull the key switch connector off the back of the key switch and check the following:
You should have +12V at all times on the Black/Red wire. If you do not, check that the Amp Meter is hooked up. If both the White/Blue and the solid White wires are connected to the back of the Amp Meter check that BOTH of them have +12V on them. If only the solid White wire has +12V, you have a bad Amp Meter. Replace the Amp Meter, or temporarily bypass the Amp Meter by putting both wires on one terminal and re-test.

If you do get +12V on both wires, plug the key switch connector back in verifying again that the Black/Red wire is going to the AM terminal. Put the meter on the Black/Yellow wire and turn on the key. You should get +12V. Now put the meter on the Black/White wire and turn the key to start. You should again get +12V. If you do not, you may have a bad key switch.
 
It will crank using a jumper wire. I will pull out the switch and check it as well as the wore run to the starter. Thanks

a possible Needed parts replacement solution Exists , if your in-dash

key switch turn out faulty or the Pig Tail that plugs into it , maybe too ?


Please See Link Below :



this is a OEM toyota New switch , and My Custom OEM Parts made Pig Tails , that are 10ga Wire Thick over sized .............

heavy duty all the way !
 
It looks like the PO cut off the connector so each wire is connected to the switch independently, so I think I had one wire on the wrong terminal.


This is the Needed Parts Solutions repair and restoration Kit i offer in my online

parts store ,

it's a OEM TOYOTA Genuine parts Lock switch , and ALL OEM Parts Maker

YAZAKI Service spec. Repair Connector Pigtail , made 1 wire gauge size bigger

using 10ga Copper Strand GTX Premium wire


kit also comes with qty x 4 3-M Heat shrink Adhesive lined BUTT connectors

for a VERY positive and SAFE factory Focus Point Mind-Set Approach Repair

where , Heavy Duty and Long Life are the Kits main Themes .................


DSCN1165.webp
DSCN1166.webp
DSCN1167.webp
DSCN1168.webp
DSCN1169.webp
 
in addition ,

this holiday season ANYONE who places a order with my online parts store

receives a FREE Poly-Carbonate Instrument cluster meter inspired key chain !



anyone who simply wishes to receive a free key chain at NO COST , please simply

pm me and one will be sent out with as a XMASS 2019 Gift !

Thanks

matt




DSCN1175.JPG




DSCN0976.webp
 
Back
Top Bottom