No reverse lights or dash indicator

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

The Prk/Neutral switch will get you home - but doesn't solve the problem. You still won't have lights on the back.

Loosing the lights can also make it so the vehicle won't start without tripping the Prk/Neutral switch.

IMHO YMMV
 
When I adjusted the Park/neutral Switch on my rig the R light and the reverse lights both started working again.
I do not think that it is a coincidence, and this was almost a year ago and all is still good for me.
I do not not know to what extent their problems are, but it worked for me.
 
In my case the symptoms were intermittant and MUCH worse in cold weather. Last year all the dash PRND32L indicators and my reverse lights stopped working around the end of November and magically started working around April. This year the same thing happened when the temperature started getting close to freezing. Often, the lights would not work until I had the engine at operating temperature, then everything would be fine. Trying to wiggle the connection at the transmission did nothing so I followed the wiring and looked for the next connection, which is between the engine and firewall.

Last week I finally managed to get an arm down there between my engine and firewall and wiggled and pulled at the large grey connector and everything started working again. It's been perfect since, regardless of temperature.

I don't know what access is like with the FZs but it's TERRIBLE with my 1HD-T. I've got long skinny arms and I don't think I'd be able to actually disconnect the connector without a whole bunch of other stuff moving first.....
 
Last edited:
same here with the temp correlation; first cold snap here and out they went. :frown: still need to get in there, but low priority.
 
I tried adjusting the sensor... nothing.. lights never came on... I suppose I'll get a good electircal friend to peep my rear trailer harness.
 
In my case the symptoms were intermittant and MUCH worse in cold weather. Last year all the dash PRND32L indicators and my reverse lights stopped working around the end of November and magically started working around April. ....

Sure can't wait until April then!
I'm still chasing this demon...
 
I noticed I have the same problem. No reverse lights and no dash indicator lights. I got under the truck last night and tried adjusting the P/N safety switch. Nothing. I got to the connector and got it dis-connected. I saw a bit of corrosion on the pins, so I cleaned them off and took a very small flat head screwdriver to try and remove any corrosion on the female side. Put it back together and still NOTHING.

What gives?

I don't have a tow harness. At least my truck didn't come with a tow package and I haven't towed anything. There are some wires and a connector under the rear though.
 
I fixed mine... I went back to a 3FE/A440F... LOL:flipoff2:
 
I sourced a replacement used Park/Neutral Safety switch and swapped it in. Still nothing. I really doubt both switches could be bad.

Anyone have any advice on what to check next?
 
My indicator lights were working the other day. At least I saw the D light on as I was driving down the freeway. As soon as I put it in reverse the R light did not come on and when I went back to D the D light was not working.

Anyone?
 
I sourced a replacement used Park/Neutral Safety switch and swapped it in. Still nothing. I really doubt both switches could be bad.

Anyone have any advice on what to check next?



I had the same issue a few years ago. The problem is the pins on the engine side (of the NSS) were too corroded to make a good contact. I ended up rebuilding the engine side and the NSS side with 2 4 pin waterproof connectors.
Then make sure the NSS is properly adjusted, it doesn't take much to be off.
 
I had the same issue a few years ago. The problem is the pins on the engine side (of the NSS) were too corroded to make a good contact. I ended up rebuilding the engine side and the NSS side with 2 4 pin waterproof connectors.
Then make sure the NSS is properly adjusted, it doesn't take much to be off.

In the end this is exactly what needed to be done. Beyond my level of expertise, I also wanted the harness checked for and shorts and be sure every part of the ignition system was working properly. I had my mechanic test every length and rebuild the connections between the NSS and the harness. Now all the indicator lights work and the reverse lights work.... and I should hopefully have no more intermittent starting issues. Rebuilding this connection on both ends is a very wise investment in time, money and/or both. It ended up costing me $300.... which included a minimum of 5 hours labor and diagnostics.
 
In the end this is exactly what needed to be done. Beyond my level of expertise, I also wanted the harness checked for and shorts and be sure every part of the ignition system was working properly. I had my mechanic test every length and rebuild the connections between the NSS and the harness. Now all the indicator lights work and the reverse lights work.... and I should hopefully have no more intermittent starting issues. Rebuilding this connection on both ends is a very wise investment in time, money and/or both. It ended up costing me $300.... which included a minimum of 5 hours labor and diagnostics.

Glad you got it figured out. I had a feeling, by your description, that this was your issue.
:cheers:
 
I had this problem awhile back and I adjusted the cable actuator thingy ( can't remember the name of it)
If I remember it is on the drivers side of the tranny and has 2 bolts that you loosen to adjust the unit.
I adjusted it alittle bit and my R dash indicator and reverse light boths work fine now.

I had the same problem and has been researching this for weeks. My mechanic advised to buy a OE from toyota and the cost was about 300 for the part and 100 for labor. I saw was you did here and tried the same exact steps. Worked like a charm(: Thank you
 
Back
Top Bottom