Newbie needs Real Time Help

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 5, 2006
Threads
2
Messages
12
I have been sitting on the side lines long enough. I now have an issue with my beloved 97 LC:crybaby: . There is an awful noise coming from under the front end of the vehicle. The sound is not coming from the engine, but seems to be coming from the drive train. I can only compare the sound to a tin can with rocks in it. Any suggestions on what to check first?

Thanks
 
Welcome to the world of Landcruisers:

Does the noise occur with engine running and vehicle not moving?

If noise occurs with vehicle moving, does it get worse when turning. Check under cruiser, front wheels, ball joint and see how greasy they are.

Do u have the FSM (Factory Service Manual)?

When was the cruiser last serviced?

How many miles on said cruiser?

Any modifications to said cruiser?

If said cruiser has original running boards, they loosen up over time. Tighten the mounting bolts.

The exhaust heat shields will rattle like hell on some of these vehicles. With the cruiser running and parked; you can hear the tin can noise; crawl under the passenger side near the exhaust and listen. U may hear clearly what is making the noise. Be careful, it really hot. Mine still rattles and don't care!

...
 
Only makes a noise when driving not when stopped. RPM has no bearing on sound. More audible at lower speeds, but still noticable at higher speeds. Handling has not changed. I just drove it this AM when I noticed the noise.
 
Ball joints = greasy

Noise does not get worse when turning

Do not have factory service manual

Just crawled out from under the truck and there is no noise when running but not in motion.

Only makes noise in drive, not reverse.

Any other suggestions?
Last service 3mos ago. Oil change and tire rot.

101k mi. bought last June with 84k from original owner

Has front and rear lockers

Cruiser is stock. No mods yet
 
My .02,
Crawl under the PS and touch the heat shield around the exhaust (make sure car has been off it will be hot, or use gloves). See if it moves/rattles. Turn rig on get back under and hold the heat shield to see if the rattle stops. If this is the case go to Lowes etc. and get two 3inch hose clamps. Put them around the heat shield and you're set. If that does not seem to be the trouble then wait for the other gurus to chime in. I'm sure they will be able to help you out, given the correct info. In the mean time try to search a little bit, even if you don't find the answer to this question you'll stumble across countless other interesting things. Good Luck and Welcome:flipoff2:
 
I'm gonna go ahead and guess your birfs are worn (maybe broken?).

Has the front axle been rebuilt recently?
 
This vehicle has not seen any off road action....yet. Is it easy to damage the birf on road? The front axle has not been rebuilt.
 
Isolated noise to DS front wheel. Jacked it up. Slight movement when holding tire at 3 and 9, however, lots of play when rocking at 6 and 9.

Wheel bearings?
Trunion bearings?

Any other ideas?

PS Thanks for all the advice so far.
 
B, you and J need to remove that wheel and check the wheel bearings. I bet they didn't get tightened correctly when the previous owner did the knuckle job. Either way, once you two open it up, you will know exactly what you need. We got all the tools and knowledge, you just may have to get some parts.

Basically, what FZJFillmore said.
 
Bfree;


If u had new tires installed, it is possible that the lug nuts on one or more wheels are loose. They should be torqued to around 75 lb-ft. use ur lug wrench in the tool kit to check on this.

If u are fairly sure that the front axle has never been serviced, u could have a worn drive flange or dry birfield joints or loose hub nuts (54mm)
https://forum.ih8mud.com/showthread.php?t=132863&highlight=birfield+fix

Damage to the birfield ball joints is rare in standard road service. What usually happens is that the front axle receives no service (should be done around every 60k miles) and the bearings &/or the birfield joints dry out , wearing things down and causing severe damage. U may have to find a good mechanic with a lift and knowledge to help u with this.

It looks like Post#13 may have hit this.

...
 
Could contribute to the play, but not the sound. I'm thinking a wheel bearing is toasted.
Ah, makes sense. I forgot about the sound for a second.
 
Could contribute to the play, but not the sound. I'm thinking a wheel bearing is toasted.


Agreed. If it's been this way a long time, tightening the hub may not solve the problem. Like concrete says, if the bearing went and caused the loose hub, it can take other things with it (spindle). Try tightening it and see what that does for you.
 
jfz80 @bfree's

vehicle had unknown ''axle service'' before the purchase-- only meaning i dont know how far he really went. the six bolts b/w the wheel studs are new on both sides, showing that he had been in there. im thinking wheel bearings may not have been torqued to spec?

w/ both wheels up turning the pass. wheel you can hear the clicking/clunking as the usds makes its revolutions.

w/ driver wheel off lots of play in the rotor while caliper remains still. the 4 bolts on the steering arm are tight

in a time crunch cause its the DD and only kid hauler. i got a work obligation at 5 today and looks like its heading to the mechanic, but id like to give him all the info possible.

thanks so much
 
Back
Top Bottom