Newbie Intro and Question

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 29, 2007
Threads
6
Messages
16
ter researching JDM Diesel trucks for for a year I took the plunge, bought a '92 HDJ81 with 103,000 km on the clock and imported it from Japan. During my search, I found my way to this site and lurked for a while. No doubt the community on this forum had an impact on my decision (that and Toyota's reliability reputation.) I love the truck, so far I've only had 1 chance to drive it (from Richmond BC to Pemberton BC on a travel permit.) It's going in for compliance inspection next week. Once that's done, then the spending begins.

I've attached pics, from the docks in Japan and in my driveway - Yahooooo!!! My dog couldn't understand why I had the camera out and not pointing at him, so he got in the mix.

Now for the question(s):
I didn't get service records so I'll assume any maintenance that should have been done recently hasn't been. I know about the big end bearing issues with these engines and plan to do the BEB right away. Anything else I should do on this truck at 100K (timing belts etc?)

Looking forward to lots of fun in the new rig.
HDJ81-0018955%20(2).webp
DSCF1123.webp
 
Lots to do. This has been covered many times. But here is my 2 cents worth.
No timing belt...chain and that should last you to 300k miles.
Heres what I did on my 95 80.
Wires, plugs, rotor, distributor cap, all liquids (brake, power steering, motor, differentials) Hoses, belts, brake pads (100 series on front) Inspect and clean ERG, birf job with synthetic grease, wiper blades, PHH hose, upgraded headlights to John Deere, also check your tie rods for wear. Also check out the alignment. Shocks replaced and a good waxing. Check front and rear windows for leaking.

I am sure I have done a few more items but for the life of me.....maybe I need another cup of coffee. Good Luck and welcome! :flipoff2:
 
Lots to do. This has been covered many times. But here is my 2 cents worth.
No timing belt...chain and that should last you to 300k miles.
Heres what I did on my 95 80.
Wires, plugs, rotor, distributor cap, all liquids (brake, power steering, motor, differentials) Hoses, belts, brake pads (100 series on front) Inspect and clean ERG, birf job with synthetic grease, wiper blades, PHH hose, upgraded headlights to John Deere, also check your tie rods for wear. Also check out the alignment. Shocks replaced and a good waxing. Check front and rear windows for leaking.

I am sure I have done a few more items but for the life of me.....maybe I need another cup of coffee. Good Luck and welcome! :flipoff2:

drsales -
This is a diesel motor so much of the above won't apply. No PHH. It does have a timing belt, no spark plugs, etc.

Pemby -
The bulk of the 80 section members drive petrol rigs. However, several of the AUS guys on here will be able to provide some good advice on the diesel side. There is also a toyota diesel section on 'mud.

Nice rig and welcome to the forum!
 
One day I'm flying out to BC to drive back one of those beautiful diesels that seem plentiful out there.
Great looking truck.
 
Yeah, it's got a bit of a "poser lift." I figure it was more show than go as it still has the ubiquitous running boards on it. I'll probably still have to start from scratch with susp mods.

Matt
 
Cool truck - Im diggin' on the Asian headlight washers and the fender mounted side view mirror. You have the opposite of the usual stinkbug stance...depending, you could get a spring spacer for the rear and level her up. What are the specs on the Deisel motor anyway? curious ...great torque for crawling - good luck and have fun with your new toy! :beer:
 
Nice rig I wish we could get those here in the states.....
 
WOW

Wow, I just realized only 103 kilometers which is only about 65,000 miles . Holy c**p!Thats like 4200 miles a yr. sHAZAM! What a find - It looks very clean and reflects the low miles. Please tell us the story on how/why/who on importing via Japan. Costs involved? At the end is it still reasonable?

I know there are some great threads and folks here that can help you with the deisel portion of your questions. Also chk out the search function.
 
Hey Matt, welcome from Squamish. If you scroll down the forums page you'll find the JDM section and the Coastal Cruisers pages. They are more local and more diesel specific, however, there is a ton of info on this site in general. Can you get your inspection done up there or do you have to come down to Cambodian Tire here in Squamtown? Take care and maybe see you on the trail, Greg.
 
I would be wary of some of the advice given by those unfamiliar with the HDJ models, no matter how well intentioned the advice is.

The most pressing issue outside of the BEB would be ensuring that the headlights have been changed to suit travel on roads suited to LHD vehicles, this thread should help you out:
https://forum.ih8mud.com/showthread.php?t=140609

The timing belt should be done at 100k, there is a light that comes on and needs to be reset. If it has already been done there should be a sticker on the timing belt cover similar to below:

11476-21.jpg
 
Just as Jasonmt says, timing belt and BEB's a must on 1HD-T after 15years and 100k. E code headlights (LHD) can be obtained at ATEB in Vancouver. Great truck! Tony
 
Welcome!

I hope you at least took the scenic Richmond to Agassiz to Pemberton route instead of the boring old Sea to Sky...

Great rig. There are quite a few Vancouver-based HJJ81 owners on this forum - you guys could start your own club.

Check in with some of the local clubs down in the "International" section of 'Mud, and I'm sure you'll find someone hear you with the same model as yours.
 
JDM 80's

Yeah, it's got a bit of a "poser lift." I figure it was more show than go as it still has the ubiquitous running boards on it. I'll probably still have to start from scratch with susp mods.

Matt


Don't write off the running boards. They make access into the truck much easier. Just don't forget that they are not sliders and they wil survive for a while.

On the Service aspect of ownership of a JDM Diesel cruiser. Filters, Fuel, Oil, and Air are always important.
I would also check and change if neccessary all the Oils: Diffs, Transfer, Power Steering, ATF and drop the Auto trans pan and check the magnets and filter.
What do the swivel hubs look like??

Is it late 92 with 16 inch wheels?
If So:
The brakes disks in front should be 32mm thick and the scrap limit is 30mm. Rear disks 18mm thick and scrap limit is 16mm.
Also check the wheel bearings and adjust if neccessary. Don't forget the rear wheel bearings as they also need love. They are the same as the front wheel bearings in the late 92 JDM with the ful floater axles.
Also if you ever need to have work done on the injector pump have them check the cold start system in the pump. There is a small metal piece in there that can wear and break off. (happens occasionally)

Have fun
 
Last edited:
Nice looking rig. I was seriously looking at a diesel when I bought my 80 series. The import costs, and hassles, to the US were what steered me away. Having a dad who was a diesel mechanic for 21+ years has given me a soft spot for diesels. Awesome rig, get all the PM done and get her out on the trail ASAP!:cheers:
 
The lift turned out to be a Rancho lift, needed new shock bushings once we got into it, those should be in next week.
 
Welcome, Welcome......:flipoff2:........ another sweet hdj from japan.

Looks like about a 3 inch lift, all you need now is a set of real tires and you will conquer most anything.
I don't know how the deisel does with 35s but I will never go back to anything smaller on my 80
 
Wow, I just realized only 103 kilometers which is only about 65,000 miles . Holy c**p!Thats like 4200 miles a yr. sHAZAM! What a find - It looks very clean and reflects the low miles. Please tell us the story on how/why/who on importing via Japan. Costs involved? At the end is it still reasonable?

I know there are some great threads and folks here that can help you with the deisel portion of your questions. Also chk out the search function.
I knew I wanted a diesel 4x4, I researched online for a year (casually, you know the mostly killing time on the computer kind of research) trolling through Japanese exporters websites, tradecarview.com is one of the best and through sites like ih8mud, just trying to figure out what kind of truck to buy. Once I'd decided on a cruiser I found a company called Kana Trading Company in Japan. I'm not sure if I'm allowed to attach their email address/URL to this shameless plug, so I won't but google them if you're curious! Masa at Kana trading was awesome, he had a truck listed at a really reasonable price that he had just sold. I gave him all my requirements (Diesel, ~100,000km, auction grade 3.5-4.0) within 2 weeks he was in touch to tell me there was a truck that fit my requirements at auction. He gave me the ballpark price and I told him to go ahead and buy it. No deposits or any of that other bs required (I've heard some horror stories about people that have sent deposits and can't get them back.) At the auction, Masa picked up the truck cheaper than he quoted and passed on the savings to me.

I shipped it in a container (only way to get here in a reasonably short time.) By the time the dust settles, I'll be into this thing for CDN $14,000 including customs clearance, duty, taxes, compliance inspection and work involved to clear it (DOT headlights etc.) and the do it now mechanical stuff (repl all fluids, BEB and timing belt.) I just made sure I was organized with my paperwork and did everything I could to make the process painless for Masa and the customs broker I hired and all went super smooth, they help you through the process.

Overall you gotta be patient because the process takes 8-12 weeks from start to finish and you have to be able to pay for the vehicle up front and drive something else while you wait.

Would I do it again, definitely.
 
Back
Top Bottom