Newb 4WD Question

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 25, 2006
Threads
41
Messages
257
Location
Al Ain, UAE
I'm finding some conflicting info, so hope you guys can set me straight.

AFAIK, my 1994 LC-80 is a part-time 4WD vehicle - it runs on rear wheeldrive and the front axle is not normally engaged.

There's a "H4" button on the dash that engages a central locking differential and shares torque 50-50 to the front and rear.

There are automatic locking hubs on the front wheels.

Is this correct?

Also, is there any procedure for unlocking the front wheel hubs when coming out of 4WD?
 
OK, no takers - I guess it's too dumb a question! :D

Maybe this will help: the part I don't quite get is the center locked diff.

If I'm in 2WD and I press the H4 button, the front engages - fine. That's because the center diff locks up? or is it just engaging the front without locking it and without necessarily splitting the torque 50-50 front-rear?

Then if I go into LO, the center diff stays locked just the same as in 4WD HI?

From what I understand, people do the pin 7 mod to be able to unlock the CDL in LO and drive it open, just like in HI... and that's where I get lost, as it apparently contradicts.

"CDL Switch- Center Differential Lock Switch- Switch installed to allow the Center Differential to be locked when the transfer case is in High." - is this my H4 switch?

Sorry I'm so confused - just trying to get my mind straightened out.

EDIT: CJF, yeah, I guess I am - I've read the FAQ, and I think I covered most of it. And I downloaded the Owner's Manual, where it talks of this CDL button I don't have. So I'm just looking for an explanation.
 
Last edited:
Does sound like you're different. :D

If you've read the FAQ, you know US models have no 2WD: it's either open center diff 4WD (AWD) or locked center diff 4WD.

Best way to learn about your specific vehicle would be to see for yourself: For example, if you think you have a "2H", put the tranny in park (engine off), t-case in, what? 2H? Does it say that on it? Anyway, then jack up one front tire. If it spins, then yeah, you have 2wd (rear wheels). If indeed it spins, note also whether the front driveshaft is spinning.(That would tell you whether you have hubs that can be locked/unlocked.)

You can figure out everything you need to know about how your driveline works with simple experiments like that.

Keep us posted; this sounds interesting.

Curtis

P.S. Hey, how about some pic's of your cabin, like the T-case shift lever and switches? Folks could tell you if they're different.
 
cdl

hey prossett,i think your cruiser will be a part time 4wd like the New ones that were sold down here,not like the full time 4wd ones in the states,i also think it was on the early 80`s also up to a certain year,once you hit that h4 button she goes in to 50:50 split like hitting the diff lock switch an a vc / fulltime 4wd model, a lot of 70`s and hilux use the same system also some have auto hubs some manual.to unlock your front hubs im pretty sure you just reverse up a few metres after youve taken it out of 4h you might here a click when they disengage,hope this helps:D
by the way prossett had a look through some of your pictures from the desert they are amazing!!!:eek:
 
If you have a button for 4H, then more than likely your first guess was correct, with the exception of the center diff locking. Part time 4wd does not have a differential in the tranfer case. When you engage the 4H switch, you engage the front axle with the tranfer case gears, there is no slipping. The auto hubs should unlock rolling backward in 2wd as was posted above. Hope this makes sense.
 
My interpretation...

His truck is indeed AWD just like ours (US) in this respect. His has a CDL button but no pin 7 mod. I.e. the CDL (H4) button engages the center locker in high gear. It is only labled different. If he were to do a pin7 mod, he would then be able to UNLOCK the center diff while in low gear.

There is a substantial chance that there is a wiring difference. So before doing the pin7 mod to your non-US spec truck, trace down the wires and make sure they're doing what the mod faq says they should be doing.

I think the H4 button for the Middle East is just like the Center Diff button for the Australian/Japanese markets. Just a different color/graphic.

This is all just a theory...
 
Thanks guys - looks like I need to be careful what I read applies to my truck... since I bought her 2-3 weeks ago I've read everything I could find about the 80, and downloaded the FSM for US specs, and the great quality info on this forum - but it seems I need some time to digest. :grinpimp:

As CJF said, best I start from what I've got and then work my way up from there, rather than read about it and work my way back.

I'll keep you guys posted, as I guess a weird Middle East spec LC-80 is novelty. Actually, it's a major market for Land Cruisers.

My first intro was here , with pics. To save you going through them all, here's the one with the dash H4 button, and you can just see the t-case shifter: it has 3 positions; from the top: H - N - L.

controls.jpg
 
locker buttons

Sounds like IDing all aspects of drivetrain is not so straightforward. I was not able to pull up topic in FAQ. I am looking to buy and 80 series and want to be able to lock the t-case and the axles. I have seen a rotating knob type switch for front and rear lock, an H4 button, a " center lock" button, and a button indicating a schematic picture of center lock.

In the FJ-80 and FZJ80, what buttons do you need to have both the center and both axles locked up?

Please help out a jeeper who just realized that a LC-80 is much better and much less expensive and much cooler than the new soccer mom Rubicons!! Good trucks are going extint.

Is there a post of photos of all locker buttons switches on 80 series? Most of the people now selling these things have no idea what a diff locker is.
 
Sounds like IDing all aspects of drivetrain is not so straightforward. I was not able to pull up topic in FAQ. I am looking to buy and 80 series and want to be able to lock the t-case and the axles. I have seen a rotating knob type switch for front and rear lock, an H4 button, a " center lock" button, and a button indicating a schematic picture of center lock.

In the FJ-80 and FZJ80, what buttons do you need to have both the center and both axles locked up?

Please help out a jeeper who just realized that a LC-80 is much better and much less expensive and much cooler than the new soccer mom Rubicons!! Good trucks are going extint.

Is there a post of photos of all locker buttons switches on 80 series? Most of the people now selling these things have no idea what a diff locker is.

Real quick and short...
Welcome :flipoff2: .
Use the FAQ for US (United States) spec newbie guide.
prossett is a VERY special case as he is in the UAE (United Arab Emirates) and has a very non-typical (from the US perspective) crusier. We're all excited to see it and understand the little different bits.

For your purpose, assuming you're in the US, you shoudl check out the faq at the top of the 80's section (its a 'sticky' post).

Now, back to our regularly scheduled non-US spec vehicle drooling...
:bounce: :bounce2:
 
prossett, what do your front hubs look like preferably with the hub caps off? That should help us identify what's going on with the front axle as far as part time goes.
 
Prossett, do you have an owners manual? It should tell you what you need to know, about 4wd, locking/unlocking hubs, etc.
 
A little update on this as I progress in understanding more about my rig: I'm pretty sure it's part-time with auto disconnecting hubs. With both front wheels off the ground, I can turn one by hand and the other does not turn.

I'm trying to get a copy of the original owner's manual.
 
My first intro was here , with pics. To save you going through them all, here's the one with the dash H4 button, and you can just see the t-case shifter: it has 3 positions; from the top: H - N - L.

controls.jpg

Nice throtle control....I thought that was what the pop-out would be for (FJ40 style) or is that a manual choke?.
Does your truck have two factory fuel tanks ....what is the "fuel pump" switch for?

Very interesting
 
It's a hand throttle, I guess for when winching and you're out of the vehicle but need it revved up. I'm not sure what else you'd use it for, maybe it gives more accurate control than the foot pedal... Yes, dual tanks, and that's the sub-tank switch.
 
Back
Top Bottom