New plugs/wires = hot engine???

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 13, 2006
Threads
114
Messages
634
Location
West of the Pecos
Howdy all,

I changed the plugs and wires in my 3FE last weekend (all OEM from CDan) and yesterday took a 50 mile drive down the highway and noticed my temp gauge seemed to be reading a little higher than it was before. For some reason the OEM plugs that I took out of the truck were gapped to 0.038", but I gapped the new plugs to 0.043" as per the FSM.

Any reason why any of that should make my engine run a little hotter?

Is it possible I knocked something loose that would cause this? I don't think it's really "overheating", and the ambient temp was about 90F, so it may not be an issue... Just seems like the temp needle was always right in the middle before, and now it's just below the first mark down from the top.
 
nobody knows nothin', huh?
 
My personal thought would be that it's highly unlikely that replacing the plugs with new OEM ones could be causing noticeably higher running temp's.

Given that, I think you *are* right to be concerned about the temp's: With these rigs, any gauge readings over exactly halfway (where there is a well known dead spot) are not good and should be looked into.

For example, how old are your fan clutch, thermostat, and radiator? All original??

Curtis
 
...For example, how old are your fan clutch, thermostat, and radiator? All original??

Curtis


Radiator had a cracked top tank back in February (I think) so I replaced the whole radiator and the thermostat then - both OEM from CDan. I'm not losing coolant anywhere, and the coolant is the right stuff - not "Dex-Cool" or any mix thereof.

Fan clutch? I dunno... It's still the same one that was in it when I bought the truck in May '06. I do know that the fan did not spin freely when I turned it by hand the other day.
 
How much is a little?

Larger gap, wouldn't that create a larger spark? larger spark = more heat. Just a thought
 
How much is a little?

Larger gap, wouldn't that create a larger spark? larger spark = more heat. Just a thought

Gauge up "a little" means it WAS smack dab in the middle. Now it's running about half way between the "middle" and the hash mark above the middle.

What you said about the spark is exactly what I was wondering. My thinking is the larger gap might be making the fuel burn faster/hotter and causing the engine to run a little hotter... but my gut tells me the temp gauge is probably not sensitive enough to read the difference.

Maybe I'll just order up a fan clutch from CDan and see what happens. The one in there now might be 16 years old for all I know.
 
If the distributer was loose its possible that the timing was changed unintentionally, which can cause it to run hot.

Or maybe the plug wires were installed one cylinder advanced or retarded?
 
What you said about the spark is exactly what I was wondering. My thinking is the larger gap might be making the fuel burn faster/hotter and causing the engine to run a little hotter...

I understand exactly where you guys are heading with this, but: OEM plugs gapped to FSM spec. should *not* result in higher than normal running temps.

I suppose you could get more accurate temp. readings (aftermarket gauge, IR gun, ...), but really, I'd look elsewhere.

Edit: Heck, if you really suspect the new plugs, put the old ones back in and see if the temp's go back down. :meh:

Curtis
 
New plugs/wires would not change engine operating temp if correctly installed. Look elsewhere.

DougM
 
If the distributer was loose its possible that the timing was changed unintentionally, which can cause it to run hot.

Or maybe the plug wires were installed one cylinder advanced or retarded?


No, the distributor was okay and I was EXTREMELY careful to make sure I got all the wires plugged in right. I would think I would feel and/or hear something different if I'd plugged in the wires out of sequence...?

I went ahead and ordered a new fan clutch. It's probably the original one, and that's been in there for 16 years and 140k miles or so. Probably a good idea to replace it, even if it's not the problem.
 
Edit: Heck, if you really suspect the new plugs, put the old ones back in and see if the temp's go back down. :meh:

Curtis


The old plugs went out in the trash last week. :o

I know it probably has nothing to do with anything, but for the life of me I can't figure out why I gapped the old plugs 0.038" in the first place... I guess that's what the Haynes manual called for - I didn't have the FSM when I put them in.
 
Back
Top Bottom