New not good Vibrations

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 17, 2015
Threads
65
Messages
445
Location
Jefferson City TN
Driving over to southeast overland for gears and lockers last week I started getting a bad vibration from 35mph and up. Both axles have been completely rebuild with all new parts. But the vibration is still bad.
What else could it be. A shake test on the driveshafts don't reveal bad Ujoints. Any know?
 
Should also add I lifted it 2 weeks ago with OME j series up front and OME heavies in the rear. With caster correction brackets. All purchased from cruiser outfitters.
 
Shake testing of u-joints will only tell/show you that the joint is completely shot. In order to test each u-joint properly you need to drop each drive shaft and rotate each on both axis. Check for complete smooth operation. A tight "good?" u-joint can have a hard spot in one of the rotations and will give you vibrations.
 
Shake testing of u-joints will only tell/show you that the joint is completely shot. In order to test each u-joint properly you need to drop each drive shaft and rotate each on both axis. Check for complete smooth operation. A tight "good?" u-joint can have a hard spot in one of the rotations and will give you vibrations.
Shake testing of u-joints will only tell/show you that the joint is completely shot. In order to test each u-joint properly you need to drop each drive shaft and rotate each on both axis. Check for complete smooth operation. A tight "good?" u-joint can have a hard spot in one of the rotations and will give you vibrations.

Thanks, will it hurt it to pull each shaft 1 at a time and drive around the block as a test?
 
I should also say that it is more than a little vibration. It is like a cinder block is tied to a tire...
 
Thanks, will it hurt it to pull each shaft 1 at a time and drive around the block as a test?

You can do that. You need to lock the center differential. Do you have a CDL switch?
 
Are 80 series drive shafts indexed? Externally weighted? The shop still has the cruiser from the axle rebuild, gears and lockers but they can't find the issue. Very very bad vibe at anything above 10mph.

Needing some suggestions on things to check. I am 3 hrs away from the shop so I can't just go grab it to diagnose.

Need a little help guys
 
Can you tell which direction the vibration is coming from, left/right front/rear wheel, engine bay, center area? Tires, wheels, lugs, wheel bearings, birfield joint, motor/tranny mounts, ??? Can you put the Cruiser on a lift and run it through the gears while someone inspects things?
 
J spring lift usually will require a double cardan front drive shaft to avoid vibration.
 
J spring lift usually will require a double cardan front drive shaft to avoid vibration.

I am J up front and heavies in the rear. It drove fine for around a week then this issue started with what I thought was a Ujoint going out(about 40 miles from shop) after axle rebuild it has gotten worse. Like cinder block tied to front tire bad. Not drivable.
 
Would installing all 4 new tie rods cause it? Haven't aligned it yet.
 
Are 80 series drive shafts indexed? Externally weighted? The shop still has the cruiser from the axle rebuild, gears and lockers but they can't find the issue. Very very bad vibe at anything above 10mph.

Needing some suggestions on things to check. I am 3 hrs away from the shop so I can't just go grab it to diagnose.

Need a little help guys

It's hard to diagnose over the net, but the general rules of thumb: Tire balance usually shows at ~30-45mph, depending. Drive shaft geometry, lift related, comes in at ~highway speed, and generally is more of a annoying noise than "shake the whole rig". Low speed, under power, shake, is generally a wasted u-joint or other drive componet.
 
It's hard to diagnose over the net, but the general rules of thumb: Tire balance usually shows at ~30-45mph, depending. Drive shaft geometry, lift related, comes in at ~highway speed, and generally is more of a annoying noise than "shake the whole rig". Low speed, under power, shake, is generally a wasted u-joint or other drive componet.

I agree completely. He is saying over 10mph the shake is so bad it rattled my aux lighting loose from its mount.

The problem I am running into is I am 3hrs away so simply pulling the shafts one at a time has taken a week. They are suggestion front and rear double cardan shafts... Seems overkill.
 
If it is as bad as he is making it sound, then I have a hard time believing its a U-joint. When I did J-lift, the front DS was vibrating, but it wasn't THAT bad. When my rear U-joint went, it was more of a feeling like both my rear tires were out of balance or out of round... Driveable but just not that smooth.

The intensity of the vibe he is describing seems like it might be something totally different all together. Who did the axles? Maybe something was not re-assembled correctly? I'd probably lock the center diff and pull each DS and see if that made any difference first of course.
 
If it is as bad as he is making it sound, then I have a hard time believing its a U-joint. When I did J-lift, the front DS was vibrating, but it wasn't THAT bad. When my rear U-joint went, it was more of a feeling like both my rear tires were out of balance or out of round... Driveable but just not that smooth.

The intensity of the vibe he is describing seems like it might be something totally different all together. Who did the axles? Maybe something was not re-assembled correctly? I'd probably lock the center diff and pull each DS and see if that made any difference first of course.

It is puzzling to me too. Southeast overland in South Carolina did the ARB's 4.88's, full brakes and complete axle rebuild with the kit from cruiser outfitters.

It was drivable but vibrating when I took it in. Started vibrating about a 2.5 HR interstate drive. Figured I was loosing a Ujoint. No biggie.

Rebuilds happened and now it is so bad it can't move. I am not new to building rigs or working on them and this seems like something simple. I am just 3 hours away and I am worried that if they did in fact miss something on the install that they wouldn't cover it I pick it up.

Steve at SEO is a reliable shop and I trust him. But I am not sure how many 80's roll through his shop so I wanted to ask here.

Right now he is suggesting a double cardan up front or maybe both... Seems extreme to me. But All of his suggestions up to this point have been very sound. Wanted to confirm here
 
I blew the front driveshaft on my 80 and drove around for almost a month with just a rear driveshaft. No big deal even if you don't have a diff lock, but with one I'd have them pull the front shaft, click the button and drive it. FWIW, even with the front U Joint thrashed on my truck it still wasn't cinder block on front tire bad. I hope nothing happened with the install of the other parts. good luck!
 
It is not about trust. It is about fixing it. Your boy Steve wants you to throw down some serious ching-a-ling and can't say it will fix it?

See where I'm going?

You are going to have to take control of the fix. Brother Steve is out of ideas and is willing to drain your bank account so he can throw parts at it. You have to take the drive shafts off and work over the u-joints through their range to eliminate them as the problem. I'm just trying to encourage you to go with your gut feeling that it most likely is a u-joint. 14mm socket with a 2.5 and a 5 inch 3/8 drive extensions. If you have a 1/2 inch drive breaker bar and an adapter to get back down to a 3/8 socket, you can loosen them up quick. 3/8 drive socket slips into the tight space just right. 1/2 inch drive 14mm socket is too big. You also need a 14mm wrench. Front nuts torqued to 56 foot/#s, rear is 65 foot/# ; for the 95 - 97
 
It is not about trust. It is about fixing it. Your boy Steve wants you to throw down some serious ching-a-ling and can't say it will fix it?

See where I'm going?

You are going to have to take control of the fix. Brother Steve is out of ideas and is willing to drain your bank account so he can throw parts at it. You have to take the drive shafts off and work over the u-joints through their range to eliminate them as the problem. I'm just trying to encourage you to go with your gut feeling that it most likely is a u-joint. 14mm socket with a 2.5 and a 5 inch 3/8 drive extensions. If you have a 1/2 inch drive breaker bar and an adapter to get back down to a 3/8 socket, you can loosen them up quick. 3/8 drive socket slips into the tight space just right. 1/2 inch drive 14mm socket is too big. You also need a 14mm wrench. Front nuts torqued to 56 foot/#s, rear is 65 foot/# ; for the 95 - 97

@elhombre I know what you are saying and I am not afraid to do the work... swapped many a U-joint. I do appreciate the specs and tools list though. Keeps me from guessing.

Your setup is similar to what I am running. What drive shafts do you have? stock?
 
Tell Steve to pull one driveshaft at a time, lock the CDL , and test drive it to prove which, if either, driveshaft is the bad one. Your lift rarely needs a DC in the rear and some folks run that lift with no DC in the front.
 
Back
Top Bottom