New LX450...

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 31, 2007
Threads
6
Messages
23
I purchased a 97 LX450 w/159K a week ago and everything seems fine until today. I went out to start her up and nothing happened. The lights came on in the dash but I couldnt get it to turn over, no click no nothing. I thought it might be the battery but i just replaced it a week ago. I got someone to jump me off and it started just fine. I have a friend that is a mechanic who tested the alt and battery for me and he said they were both fine as well. Did the contacts freeze up? Could starter contacts cause intermittent start no start problems? Why would my truck start after it was jumped off? Do I need a new starter or new contacts? Sorry, but I am a newbie and I am trying to figure this out on my new LX because I am going on a trip this weekend.

BTW, I looked at the starter and it is a remanufactued starter.
 
Did you check our fuses? Mainly the IGN fuse?

It could be as simple as that...otherwise, I don't know.
 
Why did you get the new battery? Was the other giving you the same problem?
How are your battery cables? Clean and tight on BOTH ends?
 
The battery cables are clean and tight. I bought a new battery because it did the same thing the day I bought it (no start) but it would start when I jumped it off. Therefore, I thought it was a weak battery and went ahead and replaced it but now its doing it again. If a fuse were blown I wouldnt think it would start even with a jump.
 
Bad starter drawing to much current. Or bad alternator as stated above.
 
I dont think its the alternator because I have already tested that along with the battery. Its only not started 2 times since I bought it last tuesday both times I have been able to jump it off (I have started it multiple times). The only thing it could be is the starter correct? I guess the question is do I need new contacts or a whole new starter?

BTW, I just took it get aligned and the mechanic popped the tie rod ends out of the sockets... &#@*!!!!! This is not my day.
 
Woulden't be a fuse if jumping got it to start

Take an Ohm meter and measure from the neg battery post to chassis to make sure you have a good connection.

Measure to make sure you have 12V away from the battery (pick a spot) to make sure nothing appears to be loading the voltage down. Take off the battery cable and insert the meter in current snse mode from the battery cable to the post (Do not try and start) see if you have something drawing current that sghould not be.

Could be bad connections, battery being drawn down from problem somewhere, alternator not charging battery and problem with the starter including starter contacts. All inexpesnive problems if you do the work yourself.
 
I dont think its the alternator because I have already tested that along with the battery. Its only not started 2 times since I bought it last tuesday both times I have been able to jump it off (I have started it multiple times). The only thing it could be is the starter correct? I guess the question is do I need new contacts or a whole new starter?

BTW, I just took it get aligned and the mechanic popped the tie rod ends out of the sockets... &#@*!!!!! This is not my day.

Starter contacts and plunger $25 plus 1 hour of your time

New starter - ~$200 and 50 minutes of your time.


The contacts are good PM in case thats not the problem.
 
Ouch. that sucks about the Tie rods. I am holding off on an alignment until I can replace all of the front end wear items at once to try to avoid exactly what happened to you. As for the starter I would guess contacts and plunger but I'm not positive. You could always grab a deal on an OEM one from CDAN and rebuild the old one to keep as a spare..
 
OK, I am guessing since it starts fine then 10 minutes later it does not start the starter contacts are ceasing? When I give it a jump, it sends more power to the starter to make it turn over?? Does anyone have Cdans number?
 
OK, I am guessing since it starts fine then 10 minutes later it does not start the starter contacts are ceasing? When I give it a jump, it sends more power to the starter to make it turn over?? Does anyone have Cdans number?


1-505-821-7052
 
Could this be a fusable link problem? I had similar problem with a Ford trucks fuseble link.
 
Seems like typically with the starter contact problem you have the clicking noise, as if the starters getting power but the plunger's not engaging the contacts...??

:beer:
Rookie2

No, not always. My daughters 4runner had this exact problem and it was the contacts. Very similar starter.
 
One other thing you can try, have someone hold the key in the start position (when it is not starting) and tap the starter with a hammer. sometimes a hammer tap will make the contacts work and the starter will start working. If this works you can be assured that it is the starter.
 
Back
Top Bottom