Need A440 Bolt Pattern

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 9, 2006
Threads
110
Messages
2,158
Hey guys. I am in need of the bolt pattern for an A440 Tranny. I am looking into possibly making an adapter for my '92 so that I could run an Isuzu 4BD2T in front of my A440. I already have a solidworks type deal of the bolt holes for the Isuzu. (Through no effort of my own, I stole it off the Isuzu thread in the diesel section. Thanks whoever posted that.) My drafting teacher said it would be good real world practice for us to interface this with the machining students. I figure kill two birds with one stone and try to get an adapter made up. So, now I need the bolt pattern for the A440. Any help would be appreciated. Also, any suggestions/thoughts/etc. I know there is an adapter already, but I am loathe to use a GM tranny. And, I also know this has been bandied about alot, but never done. But, I still wanted to at least give it a shot. I love my A440, even though it is a pig. Thanks in advance. Later. :)
 
I would go 4L80E/NV4500, just because everyone can rebuild it or hop it up.
(only people that I would trust with my 440 is Wholesale Automatics in Australia)
 
Well, thats a ways down the road. All I'm trying to do now is get the A440 bolt pattern so I can start getting all my info square if I want to make an adapter.
 
If your serious about this then I may have a solution.

I've got a spare tranny housing that I could send you, or drop off.

What are your thoughts on the flex plate?
 
Last edited:
That would be pretty sweet. How much does that weigh? You could PM me with any pertinent info. I am going to try and start making headway on the project, and the first step is to get the measurements. Then on to other stuff like torque converters and all that would probably be just as hard. Before you go to any trouble I will check junk yards around here. My main goal was to see if anyone had already gotten the measurements because alot of guys talked about doing it, but I don't think they got that far before they went with the GM adapter.
 
I know. Everyone in the original thread was hyped up on using the A440 (or for you FZJ guys, maybe a hydraulicafied A442 : ). ) But who knows. I just want to give it a try.
 
The a440 gets a bad rap. Sure it sucks up power but so does a th400/4L80E. Properly built (ideally with a Rodney valvebody and in your case one of his low stall diesel torque converters) and properly cooled it is, to quote the guy that rebuilt mine (with a Rodney valvebody and aux cooler) and who was very familiar with the a440, "a bulldog".

Good luck with this project, sounds like fun!
 
Isn't the bigger issue if the shift patters on the 440 will match the power band in the Isuzu motor?

tis true. One can speculate that the 1fz produces low end power and doesn't spin huge RPMs. so i would ASSertain to say that it should be "close" :hillbilly:
 
Isn't the bigger issue if the shift patters on the 440 will match the power band in the Isuzu motor?

A low stall converter will help match the rpm range of a diesel. Plus wasn't the a440 put behind the 1hz? It certainly isn't a transmission for a high revving engine :D
 
The shift patterns is a very big concern. 3FE's red line is 4500, is that similar to the 1HZ/Isuzu?

I can't recall if Rodney's TC is low stall or not. The angle of the fins determine the stall speed and I have not seen the 1HZ's TC fin angles as compared to the fin anlges of the gasser A440. Providing the dimensions of the TC housing of the two TC are the same and you can get a diesel TC, I'd say try the gasser first then move to the diesel if needed.
 
That would be pretty sweet. How much does that weigh? You could PM me with any pertinent info. I am going to try and start making headway on the project, and the first step is to get the measurements. Then on to other stuff like torque converters and all that would probably be just as hard. Before you go to any trouble I will check junk yards around here. My main goal was to see if anyone had already gotten the measurements because alot of guys talked about doing it, but I don't think they got that far before they went with the GM adapter.

I would say that you need the following items to properly mate the two together. (Taking measurements at two different locations would be quite difficult.)

Tranny case (cut down if needed)
oil pump attachable to the tranny case
TC housing
TC
Flex plate
O/D planetary gear and all items that stack up to the oil pump

Also, the TC's guide ring that sets into the crankshaft will need to be considered.
 
The a440 gets a bad rap. Sure it sucks up power but so does a th400/4L80E. Properly built (ideally with a Rodney valvebody and in your case one of his low stall diesel torque converters) and properly cooled it is, to quote the guy that rebuilt mine (with a Rodney valvebody and aux cooler) and who was very familiar with the a440, "a bulldog".

Good luck with this project, sounds like fun!

what are your temps now?
 
Wow. I left for work with very few comments and come back with alot.
Jimmy- Sorry I missed your call. I was at work and it was busy. I'm a waiter for now so not much down time. I will try to call tomorrow around noon (my central time) concerning our earlier PM.

All other posters- Thanks for all the replies/encouragement/suggestions/constructive criticism. I am by no means a mechanic. However, my 3FE-A440 combo never shifts above 2000 rpm in normal driving, and on merging it goes to 4000 before I let off to shift. Now, my 80 is obviously not a rocket ship, but I usually leave the light ahead of most others, even shifting at 2000 rpm. I run 33" tires, and at indicated 40 mph, I am turning around 2000 rpm. Thats not corrected for the larger tires. At indicated 50, I run about 1800. And at indicated 60, around 2000. These all are, for the most part, good cruising speeds for the 4BD2T. That is one reason, I want to stick with the A440, because my engine is usually at low speeds anyway and the transmission obviously has enough line pressure to continue running...and dare I say thrive. : )

Anyway, thanks for all the comments, and I will be plumbing all of you for info as the project continues. Hopefully it turns out, because I would love to have that engine. Also, Rodney said if "someone" made an adapter, then he could make torque converters that would be diesel, and fit the isuzu-A440 combo. I may talk to some guys locally, but I doubt anything like the skills needed for that exist here. I imagine the easy part will be the adapter. Thanks all.
 
The shift patterns is a very big concern. 3FE's red line is 4500, is that similar to the 1HZ/Isuzu?

I can't recall if Rodney's TC is low stall or not. The angle of the fins determine the stall speed and I have not seen the 1HZ's TC fin angles as compared to the fin anlges of the gasser A440. Providing the dimensions of the TC housing of the two TC are the same and you can get a diesel TC, I'd say try the gasser first then move to the diesel if needed.

From the description that I read It is a lower stall than a stock gas a440 TC. It was intended for 6.2/6.5 diesel swaps where the torque increase effectively drove the stall speed of the stock TC way up. Apparently It was hard to get the stall down given the diameter of the a440's TC.

Edit: not sure what my temps are right now, I have a temp gauge waiting to go in.
 
Back
Top Bottom