My Lift....The Aftermath

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 24, 2015
Threads
110
Messages
2,663
Location
Orlando, Florida
....I could use some wise words from the experienced. My plan is start my lift next weekend now that temps are significantly down and my garage is cool enough to work in.
My Tough Dog 3" lift has been sat on the shelf for about 6 weeks. I have the springs, shocks and castor plates. Is there anything else I need to have on hand before I start? I don't have a new steering stabilizer but will get one in the coming weeks. I am still on stock tires and wasn't planning on changing the tires this side of Christmas so I hope the small wheel/tire combination doesn't look stupid.
I will pick up a set of 6 ton axle stands from HF. I have replaced suspension on a few trucks before but this will be my first 80. From reading posts it sounds like i do not need spring compressors. Anything else I would benefit from knowing?
My '94 is my daily driver so I don't want the shame of having to ask the wife to drop me off at work.
 
Beer.

You need beer.

And lots of paper towels.

Because every job on an 80 needs lots of paper towels.

A flat workspace
TALL jack stands
Make sure you unhook your brake line clips so you don't rip a hose
PB Blaster
Creeper
Floor jack
Toyota Jack






Oh....and beer.
 
Put the frame on the jack stands really high. You're going to jack up one side of the axle to help force the other side down, and you don't want it to come off the stands.

Make sure you loosen the radius arm bolts from the correct side. From Slee:

Now loosen the front four bolts that attach the arms to the axle housing. The bolts should be loosened and not the nuts. The nuts are locked with serrations on the face of the nut.

...

After removing the front bolts, remove the rear bolt, by removing the nut. In this case the bolt is locked in place with serrations.
​
Prepare yourself emotionally for driveline vibes. :)

The top shock nut below the brake master cylinder can be tricky. I used a couple of wobble extensions and an impact gun.
 
Guys above pretty much have it solid... also loosen the rear control arms & panhards to reset the bushings. The stock jack has helped me push stuff down when needed.
 
Make sure you jack it up far enough. I did not and had to do some interesting (read dumb things I won’t admit to) to get the front axle to drop low enough to fit the springs.

Also, a bottle jack will help to force the axle down. Some kind of puck is helpful to when positioning the second jack.

Get a nut splitter for the shock nut under the master cylinder.
 
Thanks guys, with the exception of sway bar extensions and longer brake lines I think i might have it all. Should I get the 12 ton axle stands instead of the 6 ton version? Oh and being Irish you know I have beer galore...:flipoff2:
 
Not mentioned above, you have to disconnect the sway bars (frame side), disconnect the hard brake lines from the frame, disconnect the parking brake at the rear cross member. Leave the hard lines loose until you replace them with longer ones. 3” is the magic number for the front to start experiencing drive line vibes IME. Also at 3” lift in the front the front sway bar has to be disconnected at the frame side so that the front DS doesn’t bind on the sway bar as you force the axle down to get the spring in the perch. Depending on your shocks you probably need bump stop extensions.
 
The safer the better with the jack stands. Just make sure they are properly sitting on the ground anytime you jack it up or down. I did my lift in my parking spot where I live, all hand tools and some beer!
IMG_20170309_123424576.webp
I trimmed this old socket for that drivers side upper shock bolt. Pipewrench would have helped too to hold the shock body. But I managed with some big channel locks.

IMG_20170309_123445407_HDR.webp


For the caster plates I used a electric impact and some big wrenches. Simple grinder, and some one inch ratchet straps to yank forward or backward on the axle to get the holes lined up.
20171002_132253.webp
 
Can anyone recommend a good supplier for extend brake lines?
 
Slee. Or the vendor of your choice.
 
Slee. Or the vendor of your choice.
I used manafre 7 line kit(I suggest all 7 lines). It came with everything I needed except fluid. With only doing the front pads/rotors(ebc green stuff) and the damn thing stops on a dime with 35’s.

I used the 12 ton stands because they’re taller. I have a little slope to my driveway so only do the front or back at a time. I like having at least 2 tires on a vehicle when working on it.
 
Not saying OEM isn’t a bad option, but why not get braided SS lines for the same price?
 
Back
Top Bottom