Multiple leaks

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 21, 2017
Threads
12
Messages
106
Location
Portland, Oregon
Happy Sunday folks-

So, as many of you do on here, I have some definite leaks. Some is oil and some is transmission fluid and some seems to be leaking coolant from right under the front. I'm trying figure out which ones I should start to tackle first. Thoughts are appreciated. In looking for biggest impact/priority with not taking whole engine out. Pics below but I know they won't be super helpful.

Any ideas for where's the most common leak points is appreciated.

IMG_8050.webp


IMG_8051.webp


IMG_8052.webp


IMG_8055.webp


IMG_8056.webp
 
Coolant. Engine leaks are usually gasket related, either not fastened tight enough or just old and worn. You can easily monitor oil levels and add oil as needed; Oil seals won't suddenly let go and bilge oil generally. Something else has to be in play for that to
happen. Same with a transmission. However, coolant leaks tend to do just that. Dribble a bit here and there and BAM! You lose coolant and overheat before you know it and cause yourself a lot more money usually.
 
Well, I'd keep a close eye on that hose. You asked THE loaded question, not head gasket related.

The coolant system is generally pretty solid, but a water pump failure almost never occurs with a warning (at least none of mine did). Old hoses are easy to spot; they're hard as a brick. The main upper and lower hoses are likely culprits, but the lower requires you to bathe in coolant, since Mr. T didn't put a petcock valve on the radiator. :bang: My feeling is, if these two are old, so are all the rest, and they're pretty cheap and easy (reminds me of an old girlfriend, damn I miss her)

The oil seal and gaskets are another story. Starting at the top/front: valve cover gasket, distributor o-ring, front main seal, then the dreaded rear main and pan arch seals. The transmission pan gasket is a usual suspect, along with the speedo o-ring.

The good news is that aside from making a mess, unless your oil pan gasket or plug is leaking, you really can't do any serious damage. There's a shutoff switch to prevent engine failure due to low oil. I've never had to use it, but if Mr. T put it there, I'd be willing to bet in its favor. ;)

None of the engine/transmission gaskets and seals are easy and cheap, although some are one or the other. You've definitely got a gusher there, so I'd go after that. Soak the warm engine bay in simple green, or something similar, take it to a nasty self service carwash and hose the thing down from underneath. Rinse, lather, repeat as necessary. Once you get a clean-ish engine bay, including suspension parts, you can start your triage.

Good luck.
 
Also, oil pump plate oring and the oil level switch in the side of the pan are usual suspects for oil leaks. A good washing will help you identify the leak points.

My radiator does have a drain petcock. Hard to get to, but it's there. Also, drain the block via the plug on the side of the block. That way you'll catch "most" of the coolant.
 
Mine has a valve, but by drain petcock I mean a 90° fitting so that it drains downward, not into the block, like mine does ;)
 
Well, I'd keep a close eye on that hose. You asked THE loaded question, not head gasket related.

The coolant system is generally pretty solid, but a water pump failure almost never occurs with a warning (at least none of mine did). Old hoses are easy to spot; they're hard as a brick. The main upper and lower hoses are likely culprits, but the lower requires you to bathe in coolant, since Mr. T didn't put a petcock valve on the radiator. :bang: My feeling is, if these two are old, so are all the rest, and they're pretty cheap and easy (reminds me of an old girlfriend, damn I miss her)

The oil seal and gaskets are another story. Starting at the top/front: valve cover gasket, distributor o-ring, front main seal, then the dreaded rear main and pan arch seals. The transmission pan gasket is a usual suspect, along with the speedo o-ring.

The good news is that aside from making a mess, unless your oil pan gasket or plug is leaking, you really can't do any serious damage. There's a shutoff switch to prevent engine failure due to low oil. I've never had to use it, but if Mr. T put it there, I'd be willing to bet in its favor. ;)

None of the engine/transmission gaskets and seals are easy and cheap, although some are one or the other. You've definitely got a gusher there, so I'd go after that. Soak the warm engine bay in simple green, or something similar, take it to a nasty self service carwash and hose the thing down from underneath. Rinse, lather, repeat as necessary. Once you get a clean-ish engine bay, including suspension parts, you can start your triage.

Good luck.

Hi Malleus-

Appreciate the info!

First question would be to ask if you know what that hose is for that is ripped up??? I can replace it but am having trouble finding it on the web.

I will definitely be putting the coolant hoses on my To Do list for the near future as well since I haven't flushed it in the year I have had the rig.

I also have a steam pressure washer at my disposal, do you think if would all good if I used that for cleaning up the engine bay? I think it will work better faster..
 
First of all, folks, he has a 1991 with a 3FE. Unlikely a headgasket issue, unless you ask @nukegoat ....

What you're looking at is not a hose. That appears to be a speedometer cable housing. Yes, there can be a transmission fluid leak from that. The early versions had speedo cable, but the 93+ did not. There are others smarter than I that can provide more input here.

I agree with @Malleus about the coolant leak first because that runs under pressure and those can cause catastrophic failures.

Coolant
Transmission fluid leaks
Engine oil leaks

Yes, get it cleaned off to visualize the leaks.

@jonheld and @LS1FJ40 can advise on the primary leak locations on the 3FE.

The list @Malleus supplied applies more to the 1FZ-FE (93+) than the 3FE for the oil leaks.
 
Man, it pays to pay attention! I didn't, or I would've seen the year in your signature.

I can only add that I'd steam clean everything below the water line, but unless you know for sure your truck has been waterproofed for fording, I would use a spray bottle and a brush for the upper engine bay (especially the area near the coil). You're less likely to get a mystery short that way.

I've been going through the new 80's engine bay since we picked it up two weeks ago, cleaning the electrical connectors and sealing them with dielectric. It's pain, but it's worth it, and it gives me a chance to inspect the electrical system for gremlins ;)
 
First of all, folks, he has a 1991 with a 3FE. Unlikely a headgasket issue, unless you ask @nukegoat ....

What you're looking at is not a hose. That appears to be a speedometer cable housing. Yes, there can be a transmission fluid leak from that. The early versions had speedo cable, but the 93+ did not. There are others smarter than I that can provide more input here.

I agree with @Malleus about the coolant leak first because that runs under pressure and those can cause catastrophic failures.

Coolant
Transmission fluid leaks
Engine oil leaks

Yes, get it cleaned off to visualize the leaks.

@jonheld and @LS1FJ40 can advise on the primary leak locations on the 3FE.

The list @Malleus supplied applies more to the 1FZ-FE (93+) than the 3FE for the oil leaks.

Killer info!

Just to be specific, when you say fix the coolant leak you are talking about replacing the hoses for the coolant correct?

Once i clean everything off i can report back better pics/details...
 
Killer info!

Just to be specific, when you say fix the coolant leak you are talking about replacing the hoses for the coolant correct?

Once i clean everything off i can report back better pics/details...

If you have a coolant hose that's leaking....Yes. Fix that one and any other ones that need to be replaced while you have the system drained. Replace any coolant hoses that are hard as a rock or soft and mushy (usually coated with oil). Make sure you bleed all the air out of the cooling system. The 3FE is better about it than the 1FZ-FE.

On the coolant, make sure your coolant isn't a brown sludge. If you're going to open the cooling system by replacing a hose(s), then it's a great time to do a system flush. Do a couple final "rinse-flush" with DISTILLED water, then drain down and refill with your preferred coolant, I believe green is the best for the 3FE. Also replace your radiator cap with a TOYOTA cap. It probably needs a new one, and the aftermarket caps are crap.

Be aware that a 20+ year old truck that is just starting to get used again will suffer from cracked / broken rubber products (hoses, belts , intake tube) and possibly exhaust holes if it has sat for a while. The heat from regular use will start to break it down pretty quickly.
 
Coolant leak first and foremost.

Clean it up then worry about the leaks. Just keep them topped off.
 
Well, I'd keep a close eye on that hose. You asked THE loaded question, not head gasket related.

The coolant system is generally pretty solid, but a water pump failure almost never occurs with a warning (at least none of mine did). Old hoses are easy to spot; they're hard as a brick. The main upper and lower hoses are likely culprits, but the lower requires you to bathe in coolant, since Mr. T didn't put a petcock valve on the radiator. :bang: My feeling is, if these two are old, so are all the rest, and they're pretty cheap and easy (reminds me of an old girlfriend, damn I miss her)

The oil seal and gaskets are another story. Starting at the top/front: valve cover gasket, distributor o-ring, front main seal, then the dreaded rear main and pan arch seals. The transmission pan gasket is a usual suspect, along with the speedo o-ring.

The good news is that aside from making a mess, unless your oil pan gasket or plug is leaking, you really can't do any serious damage. There's a shutoff switch to prevent engine failure due to low oil. I've never had to use it, but if Mr. T put it there, I'd be willing to bet in its favor. ;)

None of the engine/transmission gaskets and seals are easy and cheap, although some are one or the other. You've definitely got a gusher there, so I'd go after that. Soak the warm engine bay in simple green, or something similar, take it to a nasty self service carwash and hose the thing down from underneath. Rinse, lather, repeat as necessary. Once you get a clean-ish engine bay, including suspension parts, you can start your triage.

Good luck.

Uhhhmm there is a petcock on the radiator drivers side really hard to get to
 
Uhhhmm there is a petcock on the radiator drivers side really hard to get to
Yep, that's the one. It sprays the lower left corner of the block (and the driver' side steering components) until the radiator's empty. :)
 
Yep, that's the one. It sprays the lower left corner of the block (and the driver' side steering components) until the radiator's empty. :)

I'm not sure about your radiator, but all the 1FZ rads I've worked on had a hose barb directly below the petcock valve handle. I've been able to thread a piece of 3/8" (or close to it) hose up through the rad support and onto the hose barb. Then I can open the petcock valve just a few turns (don't remove it) and the coolant will run out of the hose into a container. It's not fast, but it catches every drop every time.

Hope this helps!
 
Back
Top Bottom