Minitruck brake booster

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 4, 2006
Threads
449
Messages
14,193
Location
NorCal
I answered your post in wanted as well. Mark's Offroad has a decent price on a rebuilt booster, and knowing Mark, it's probably done right. The Cardone units I think, just replace the parts that are bad often with other used parts.

Otherwise-go to the pick and pull and roll the dice for $15.

Good luck, there is no good and cheap option unless you can get a working booster in the junk yard.
 
Cruiserdrew said:
Otherwise-go to the pick and pull and roll the dice for $15.

It was $28, and in my naiivete I got a single-reservoir booster that doesn't have enough throw for the dual-reservoir MC. There were only two trucks there, both with single-res MCs.

Thanks for the pointer.
 
I pulled one from a junk yard off of a Toyota Mini. I had to make a couple of minor adjustments to the firewall, but it was nothing a BFH would not take care of. I have not had any problems with it since knock on wood. It was only around $20 too.

Jeff
 
i'm using a mini truck brake booster off of an 86 (i think it was). i think if you use a mini truck brake booster your supposed to have like a 5/16 spacer between that and the firewall or cut down the push rod thing in the back of the booster. I didn't do either and i'm not experiencing and drag in the brakes and it works great.
 
metalonmetal said:
i didn't know these could be used. are these brake boosters smaller than the cruiser ones? what's the advantage?

Yes, much smaller so they allow more clearance around the carb. The real advantage, though, is their wide availability and low cost.

If you want a rebuilt original it's $400-$500 depending on how you do it.
 
i was just looking into what's involved in using an offy c-series intake manifold with a 4 bbl holley carb, and one of the problems was lack of space because of the brake booster. and then this thread appears!
 
metalonmetal said:
i was just looking into what's involved in using an offy c-series intake manifold with a 4 bbl holley carb, and one of the problems was lack of space because of the brake booster. and then this thread appears!

My PO installed a holley 2bbl that has the same top as a 4bbl, so it has the same problem. He or his mechanic made an 8" air cleaner out of round plates of aluminum, maybe 3/16" thick with the big bottom hole and little top hole offset from center about two inches. It looks ok, works ok, and would solve the same problem.

If you absolutely must replace your booster, I'll send you my address where you can recycle it.
 
boy that SEARCH tool works great!

Bad Booster Signs.... by ME!

I went through this recently and came up with some good (and bad) options.

make darn sure you have the check valve... it's external on a lot of Toyota's and costs $60 to buy new from Yoda.... and there isn't an aftermarket source that I found
 
Klunky Chris said:
boy that SEARCH tool works great!

Bad Booster Signs.... by ME!

I went through this recently and came up with some good (and bad) options.

make darn sure you have the check valve... it's external on a lot of Toyota's and costs $60 to buy new from Yoda.... and there isn't an aftermarket source that I found

I saw that thread, and the good info is hidden by some, um, other stuff.

I got the check valve. On another thread I found with the SEARCH tool someone mentioned they got a check valve from Napa for about $5. It's not specific to brake boosters. It's just a vaccuum check valve.

I even got an OEM Toy vaccuum hose, bracket and bolt. It looks clean, even though the booster doesn't work right.
 
Back
Top Bottom