LSPV weeping

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 17, 2015
Threads
57
Messages
2,255
Location
Oahu, HI
Asking for some advice and suggestions. When I checked my LSPV today I noticed it had fluid on the bottom part of the little rubber ball that attaches to the bottom of it. It appears to be a small weep somewhere and looked fairly recent. Meaning, It only had one very small drop on the concrete below it in the last 24 hours. It didn't appear to have any other older drops where it is parked everyday. I would assume leaking brake fluid anywhere would not be good! But my questions are, how concerned should I be? Is this a drop everything and fix it immediately problem? how common is this and or is this an easy fix? Thanks so much for any advice. Here are some pics:
image.webp

image.webp

image.webp
 
Jen, I had exactly the same leak in my LSPV and had to buy a rebuild kit. Installed the rebuild kit and all is well.
 
Toyota does not offer a kit for the valve, only the rod. How did you repair it?
 
Dan, you are correct, I had to buy a new valve and rod kit. Sorry Jen for the misinformation.
 
As with all things brakes and steering it warrants attention but I wouldn't say drop everything overnight parts today type of attention. Move it up on the list however.

Mine has been doing the same for almost a year though maybe not as much as yours. If you squeeze the bulb/pouch I'd bet you'll find more fluid will escape there where it us puddled I purged mine and noticed the drop did not return as quick as i would have imagined and have just kept an eye on fluid level and pedal feel.

Whole assembly is under 200 iirc

Other options include removal if you are willing to do so. jcardona1 has a good write up and someone the other day mentioned just adding a bleeder as a plug to both the unit and its corresponding line at the master cylinder. Interesting approach and reversible.
 
There is a reseal kit for around $60 from Beno but if the problem is mechanical or hydraulic you will need to replace the valve. I had this same problem a few months ago and decided to just buy a new valve, also from Beno for around $180.
 
Now that I am no longer constricted with Toyota legalese, my recommendation:

Get rid of the LSPV system altogether.

But you are taking on liability and responsibility for your actions by doing this.

Realize there are legal and fiduciary responsibilities for this modification.

Also please drive your truck more like a truck with a 50/50 braking system as was the case 30-40 years ago.

Drive your truck like the 3 ton brick that it is. Drive it like a "land cruiser": A vehicle that "cruisers across the land".

If you want to retain a LSPV system, take out the Toyota system and install a Wilwood manual system that allows you to adjust the proportioning to your needs.

The toyota system is "load sensing"-- that's the "toilet bowl plunger". It is very poor at this due to the design.
 
As with all things brakes and steering it warrants attention but I wouldn't say drop everything overnight parts today type of attention. Move it up on the list however.

Mine has been doing the same for almost a year though maybe not as much as yours. If you squeeze the bulb/pouch I'd bet you'll find more fluid will escape there where it us puddled I purged mine and noticed the drop did not return as quick as i would have imagined and have just kept an eye on fluid level and pedal feel.

Whole assembly is under 200 iirc

Other options include removal if you are willing to do so. jcardona1 has a good write up and someone the other day mentioned just adding a bleeder as a plug to both the unit and its corresponding line at the master cylinder. Interesting approach and reversible.
Thanks for the reply, I wont stress so much about it now and will keep an eye on the fluid levels and pedal.
 
Now that I am no longer constricted with Toyota legalese, my recommendation:

Get rid of the LSPV system altogether.

But you are taking on liability and responsibility for your actions by doing this.

Realize there are legal and fiduciary responsibilities for this modification.

Also please drive your truck more like a truck with a 50/50 braking system as was the case 30-40 years ago.

Drive your truck like the 3 ton brick that it is. Drive it like a "land cruiser": A vehicle that "cruisers across the land".

If you want to retain a LSPV system, take out the Toyota system and install a Wilwood manual system that allows you to adjust the proportioning to your needs.

The toyota system is "load sensing"-- that's the "toilet bowl plunger". It is very poor at this due to the design.
Thanks for the advice Onur. I don't know if I really want the legal and fiduciary responsibilities for removing it. I will PM you to discuss replace/rebuilding options.
 
If you can get the fittings and bolts loose, it isn't that hard to just put a new one in. The subsequent brake system bleeding is easy to a PITA depending on your luck. A good time to replace the rubber line to the rear axle too since the system is apart near it...which leads to the rubber lines to the calipers which leads to new calipers/rotors/pads but then you're done with the rear at least.

I have adjusted mine LSPV slightly higher so it gives a bit more percentage to the rear brakes and does not nose dive as bad.
 
Back
Top Bottom