Locksmith Damaged Steering Wheel

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 23, 2004
Threads
145
Messages
2,071
Location
Beaverton, Oregon
I'm hoping to type all of this before the rage sweat dripping from my forehead ruins the laptop.

Long story short, I have no ignition key for my barn rescue 40. I was going to send the gas lock to @RAGINGMATT for a new key from his Toyota master set. Stupid me thought I'd take it in to the local locksmith to see if he could verify that the gas door lock and the ignition were the same lock.

After a few minutes of them insisting that my 40 should have a lock code on the passenger door lock that doesn't exist, and that them producing a key for my worn-out lock would be better than Matt's key that might be perfect but not fit my worn lock, I decided to let them have a go at building me a key. It was supposed to be ready that afternoon.

SIX DAYS LATER... Yes, six. I've been calling, and calling, and leaving message after message. Finally got somebody today. They said they couldn't do anything for me, other than pick the ignition lock and remove it from the column so they could sell me a $160 Chinese replacement. Finally got him to agree to just give me my stuff back for no charge.

Picked it up today to find that they had been apparently dragging the steering wheel around the shop face down.

So...

Angry...

IMG_7056.webp


IMG_7057.webp


IMG_7058.webp
 
I threw a very composed fit. I wouldn't be that pissed off, but this was truly a nearly pristine steering wheel before I dropped it off. Like I told the manager, I wouldn't have left it at all if I'd known it was going to be a week. They were supposed to be done in two hours. The manager almost immediately offered to pay for the locks I'd have to track down. He was curious about my source for new locks (@RAGINGMATT is great - kicking myself for not just going to him first) and said they couldn't find anything after looking all week. This makes me wonder if he knew they were the ones who broke my current ignition cylinder while they were playing with it. I told him that was great, and that it was going to be $200-ish for new locks, keys and labor to match the set. He didn't blink.

I also told him that I was more concerned about the damage to the steering wheel. I think I can sand/polish most of it out, but I know I won't be able to get it all without leaving a noticeable dip in the wheel. I'm so mad, both at myself for leaving it with these morons, but also at their ineptitude.

So, tech:
Is there any source for a '74 wheel in darn-near-perfect shape? Price that I should go back to this guy with? He said he'd take care of me, but I didn't even know what that would look like.

Suggestions for repair? Lightly sand-->polish the light scuffs and live with the deep ones?
 
I threw a very composed fit. I wouldn't be that pissed off, but this was truly a nearly pristine steering wheel before I dropped it off. Like I told the manager, I wouldn't have left it at all if I'd known it was going to be a week. They were supposed to be done in two hours. The manager almost immediately offered to pay for the locks I'd have to track down. He was curious about my source for new locks (@RAGINGMATT is great - kicking myself for not just going to him first) and said they couldn't find anything after looking all week. This makes me wonder if he knew they were the ones who broke my current ignition cylinder while they were playing with it. I told him that was great, and that it was going to be $200-ish for new locks, keys and labor to match the set. He didn't blink.

I also told him that I was more concerned about the damage to the steering wheel. I think I can sand/polish most of it out, but I know I won't be able to get it all without leaving a noticeable dip in the wheel. I'm so mad, both at myself for leaving it with these morons, but also at their ineptitude.

So, tech:
Is there any source for a '74 wheel in darn-near-perfect shape? Price that I should go back to this guy with? He said he'd take care of me, but I didn't even know what that would look like.

Suggestions for repair? Lightly sand-->polish the light scuffs and live with the deep ones?


Yes ,

there as a steering wheel fellow online

he restores steering wheels to a High Level , Like Super High ....

U will want to use his comps ,


he also has a Ebay store with all his High-End wears







396361818 | eBay

Toyota Land Cruiser Steering Wheel 9/72-7/80 FJ40 FJ43 FJ45 FJ55 BJ40 BJ45 | eBay
 
Last edited:
Locksmith guy is going to s*** himself. I told him I didn't know how many hundreds of dollars this steering wheel was worth. For those of you who didn't click the link, the answer is 17.

$1700

Unrestored one on his site in similar shape to mine is listed at $899.

I think I'm going to send these to him as a starting point and see where we go. I'm sure I'll end up trying to polish it out myself, regardless. Judging by the plastic work I've already done on the heater pieces, I'm likely not going to make it worse.
 
I saw the pics, easy fix. Most expensive part will be finding the horn buttons. There is a guy in Australia with some NOS or I can clean yours up and re clear them.
 
Locksmith guy is going to s*** himself. I told him I didn't know how many hundreds of dollars this steering wheel was worth. For those of you who didn't click the link, the answer is 17.

$1700

Unrestored one on his site in similar shape to mine is listed at $899.

I think I'm going to send these to him as a starting point and see where we go. I'm sure I'll end up trying to polish it out myself, regardless. Judging by the plastic work I've already done on the heater pieces, I'm likely not going to make it worse.


WOW! This one is $2,550 ! Are these steering wheels THAT rare?
Toyota Land Cruiser Steering Wheel 7/69-9/72 FJ25 FJ40 FJ43 FJ45 BJ40 BJ45 | eBay
 
As others have noted; call Birdhead--real name Jim. Super nice guy from Tulsa, great to chat with, keeps you posted on progress and does really nice work. In fact, if you are not happy, "it is on me" (to coin a phrase from Rounders):steer:
 
As others have noted; call Birdhead--real name Jim. Super nice guy from Tulsa, great to chat with, keeps you posted on progress and does really nice work. In fact, if you are not happy, "it is on me" (to coin a phrase from Rounders):steer:
Thanks, if you guys want to see my work I’ll post the thread, remember the beginning of the thread was when I was learning. The last half is where they start to shine.
 
Back
Top Bottom