Live Help. Stuck In Low

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 7, 2005
Threads
314
Messages
1,336
Location
Dallas, Texas
Well I started a new thread. I am stuck in low right now. The diff lock/ABS dash light is on. Can I drive it on the highway? I do not have a CDL switch but
I can use the flasher switch if needed. Where is the actuator located? Any ideas?? Please?
airlaird
 
Steve,

Start the truck and put it in low range. Back up straight about 20 yards. Put it in park. Now shift it back into hi range. Pull it into D and drive straight ahead about 100 yads at 10-15 miles per hour. The lights should go off and it should unlock.

Jim
 
Well I started a new thread. I am stuck in low right now. The diff lock/ABS dash light is on. Can I drive it on the highway? I do not have a CDL switch but
I can use the flasher switch if needed. Where is the actuator located? Any ideas?? Please?
airlaird

You should have kept this in the old thread, since it's all related.

Anyway, do what El Mariachi said in this thread, and do what I said in the other thread. Good luck.
 
No luck

Jim..no luck on that. It still remains in Low. I can hear the tires chirp when I turn. Any other ideas????
airlaird
 
Jim..no luck on that. It still remains in Low. I can hear the tires chirp when I turn. Any other ideas????
airlaird

Airlaird:

Did you do what I said? Am I on your ignore list or something?

Edit: Also, "Low" and "Center differential lock" are not the same thing. Just because your tires are chirping doesn't mean you are in Low. Are you actually in Low range? Does your truck "crawl" when you hit the gas? Or do you just have the chirping when you turn? If you don't go to somewhere with low traction and/or drive in figure eights or circles, you won't be able to get rid of the windup that's binding your differential.
 
Jim..no luck on that. It still remains in Low. I can hear the tires chirp when I turn. Any other ideas????
airlaird

So you are saying that the truck is physically still in low range though you are moving the shifter? Can you feel the shifter resistance or is it lose as if its come unhooked?
 
Sorry unclear from your posts...

Is the transfer case in low range?
Is the transfer shifter in the low range position?
Will the transfer shifter move when the primary gear selector is in neutral?
 
I think he's in high, but can't get the diff lock to unlock.

Correct. Just talked with him. He can physcially get the truck into high range, but the CDL is staying locked and the ABS is staying off, both warning lights are on on the dash. The only time I have had this problem, I was able to clear it by what I suggested in post #4 above. Any ideas?
 
Just talked with him. He can physcially get the truck into high range, but the CDL is staying locked and the ABS is staying off, both warning lights are on on the dash. And based on the driveline behavior, the CD is clearly still "locked." The only time I have had this problem, I was able to clear it by what I suggested in post #4 above. Any ideas?

IH8MUD.com Forum - View Single Post - ABS and Diff lock light won't go off

I think he has to do something to alleviate the wind up he's experiencing. That means he's got to drive in close to a circle. I once accidentally engaged the CDL on my '94 in my parking lot (I pressed the CDL lock button without paying attention). I couldn't get it to disengage, because I was on pavement the whole time. The further I drove down the ramps, the worse it got. It was hell to disengage. This is basically the same thing. If he can find a low-traction area, he can get the CDL to let go, but he's got to "unload" his drivetrain.

That's my guess.
 
FIXED!!......thankyou all for helping. Last week I used my flasher switch temporarily as a CDL switch for some driveshaft trouble shooting. Well, Landtank advised me to make sure I put the "jumper plug" (from the CDL harness) BACK IN. Well........stupid me....I didn't. This was the problem. The jumper plug is back in and all is well. Jim, BHM, thankyou for everything...
airlaird
 
FIXED!!......thankyou all for helping. Last week I used my flasher switch temporarily as a CDL switch for some driveshaft trouble shooting. Well, Landtank advised me to make sure I put the "jumper plug" (from the CDL harness) BACK IN. Well........stupid me....I didn't. This was the problem. The jumper plug is back in and all is well. Jim, BHM, thankyou for everything...
airlaird

You are a bigger man than me for admitting that. :flipoff2: Call Christo and get a CDL switch!!!!!!!
 
Back
Top Bottom