Lift Measurements

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 6, 2007
Threads
29
Messages
211
Location
Ogden, Utah
Just a quick thread, with a few questions. How does one measure how much lift he obtained after installing a lift kit? I am asking to see how much lift I got. It seems that I got alittle more than I asked for. I did install a OME 850J's and 863J's with a 1" spacer in the front. The kit is to be a 3", but, I am thinking it is in "no mans land", between a 3 and 4". I am running stock bumpers for now. This question is in relation to my vib threads and inquires. Do I need to install CC bushings with the drop brackets to get rid of this vib? Any thoughts and info on "how to" measure?:cheers:


John W.
 
Js as a 3" lift with an 1" spacer as a 3" lift? Crazy. I've always heard it referred to as a 3.5-4" lift by all the vendors. So with an inch spacer you'd be at 4.5-5" depending upon who is measuring.

For lifts, I measure from the center of the wheel to the bottom of the fender. Most folks measure from the fender to the ground. What I don't like about that method is that you get tire size involved.

One other thing, it looks like you are dealing with an FJ80. I noticed that my FJ80 reacted to J springs differently than my FZJ80 with the same springs. The FJ was a good 1/2 inch taller with the same spring.
 
Ginericfj80, thanks for the info. I am still wondering though what or how I read the measurements? So, I measured, and it is 25" on both tires to the fenders, how much lift is this?
 
5 inches of lift. Stock is 20" from center to fender. You gained 5"
 
Thank You Wrench, I was wondering and now I know. Maybe this will help in solving my vib problems and point me in the direction I need to get the proper parts. Cheers, John
 
So, what tires would be best for this lift? It is a everday driver. I was planning on 33"s, until I found the lift height. Any thoughts?
 
35's would be a nice size. Do you go off road a lot?
 
I do some, just the occasional to the moutains and hunting in the marsh and all winter long to the Ski Resorts. Heli-Skiing!!!!!!!! So, There are alot of winter conditions and the off-road dirt, mud, and rocks. I really like my BFG AT's they do very well in the snow and other conditions. Anyone with any other input on the vib issue with a 5" lift..ie..CC plate vs. CC bushings, I am very sure a DC shaft is in order..$^%*.
 
If you are going to use a DC Shaft you then need to make sure the pinion is aligned properly or you will have vibrations. The tolerance for proper alignment is actually smaller than that of the stock shaft.


The best approach would be to buy and install the DC shaft. That way you can take a drive angle reading of the front u-joint and know exactly where you are and what's needed.

Also you need to get adjustable panhards in there as well. With that much lift there is going to be a substantial shift in the axles.
 
...

Also you need to get adjustable panhards in there as well. With that much lift there is going to be a substantial shift in the axles.

Before you worry about the panhards, get/make adjustable/shorter upper rear control arms to get the rear pinion back into proper angle. The panhards aren't that critical, but the wear on the rear u-joint is a pain. Until you get it fixed, the joints like some extra grease,,,, often.
 
Hey Rick, Thanks Again for the input! I was thinking of the same, but I just wanted to be sure. It's alot of $, especially when I want/need tires and the front ARB. But, Hey A guy got todo what a guy got to do. I was wondering about Slees' do-it yourself kit on the Adj. panhards using the OEM pans and welding in the Adj. Has anyone used these and if so what do ya think of them??
 
Hey Rick, Thanks Again for the input! I was thinking of the same, but I just wanted to be sure. It's alot of $, especially when I want/need tires and the front ARB. But, Hey A guy got todo what a guy got to do. I was wondering about Slees' do-it yourself kit on the Adj. panhards using the OEM pans and welding in the Adj. Has anyone used these and if so what do ya think of them??

I used those on the front panhard. I don't weld so I brought the bar and joint with instructions to a guy who Tigs and let him do it. Not a problem so far.
 
Before you worry about the panhards, get/make adjustable/shorter upper rear control arms to get the rear pinion back into proper angle. The panhards aren't that critical, but the wear on the rear u-joint is a pain. Until you get it fixed, the joints like some extra grease,,,, often.

At my height I don't have adjustable rears and with more than 20k miles on the truck I see no need for them either. The u-joints get the standard greasing every oil change which is at 5k mile intervals.
 
Good point! I was thinking the same, I beleive panhards are more important, especially with larger tires. I do regular PM's and not to worried about the u-joints. I will be getting the do-it yourself kits from Slee on the panhards. Which would be better, the CC plates or bushings?? I do have the drop brackets for the control arms, so which is better, and I know, a DC is a must right know. Thanks John
 
Depends on where you are at. You might be able to add the bushings to what you have and be good. But if that isn't an option then either swapping out the drop brackets for 4" ones or removing the drop brackets you have and going to a caster plate is the other option.

If you are thinking about the 4" brackets start a thread inquireing about them. I have no experience with them and you should ask those who have them how their truck is set up.
 
Good point! I was thinking the same, I beleive panhards are more important, especially with larger tires. ... Thanks John

Why? You have the same rear lift as I do, my tires stuff very close to the same on both sides. The pinion angle is way off and wears u-joints, grab a protractor and measure yours. I would think that increasing joint life would be more important than having the axles look centered at ride hight?
 
Tools, U do have a good point as well! I am currently making a list of all the things that need to be done. This is one of them, but, I want to make the vib disappear, it makes me think I am doing more damage somewhere. I do have a tight LC budget. So many things to do. And what to do. Thanks John
 
Back
Top Bottom