Least difficult V8 conversion??

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 2, 2007
Threads
2
Messages
5
Location
Denver, Colorado
Website
www.ar15dealer.com
I have a nice and nearly rust free 77 FJ40 with a blown 2F that is just gathering dust in my garage and I want to get it back on the road. After some serious thought, I have decided to use a GM crate 350 instead of rebuilding the 2F. It looks like the Marks of Aust. kit would require the least modifications and will allow me to keep the original 4sp. transmission and driveshafts where they are. Are there other options that I am missing before I spend the $$ for the Marks kit? Thanks in advance.
 
You will be into a 350 conversion alot more $$$$ than just rebuilding the 2F, and if you do it right, the 2F will make plenty of power.

a 350 conversion takes alot more time, money and patience than what is required to physically fit the motor into the engine bay. You have to address fuel supply, induction (carb, tbi, mpfi, spfi, fotmfi, etc). Exhaust issues, coolign issues, wiring issues, plumbing issues. It's not the big stuff, it's all the little stuff that adds up over the course of the project.

If you are looking for 'easy' or 'inexpensive' then rebuild the 2F.
 
I know that the V8 conversion is going to cost some extra $$ and require some mods. I am really looking for the extra power that the V8 will give me, the 2F always seemed underpowered up here at 6000 ft. and it just gets worse at the 10000 ft pass up to the mountains. When the FJ40 was still powered by the 2F with 31" tires and the factory 4.10 gears, it wouldn't go over 65 and that was on a good day with a tail wind, going down hill!!!! I'm sure a fresh 2F would have more power than the current 2F but I don't want to spend the money on a 2F rebuild and then still be unhappy with the power and have to start over.

Does anyone that has used the Marks kit have anything to say good or bad?
 
You will be into a 350 conversion alot more $$$$ than just rebuilding the 2F, and if you do it right, the 2F will make plenty of power.

a 350 conversion takes alot more time, money and patience than what is required to physically fit the motor into the engine bay. You have to address fuel supply, induction (carb, tbi, mpfi, spfi, fotmfi, etc). Exhaust issues, coolign issues, wiring issues, plumbing issues. It's not the big stuff, it's all the little stuff that adds up over the course of the project.

If you are looking for 'easy' or 'inexpensive' then rebuild the 2F.

I disagree wholeheartedly. You can drop serious coin into rebuilding a 2F and still end up with a sub 200 hp 4 main tractor motor. Assuming the block isn't windowed the machine work alone to rebuild the 2F will run many hundreds of dollars. Add in NON-Toyota master kit for another $800-1200. OEM parts are gonna be more than that. Then if you need a new crank or to have yours ground...

The 2F is many things. Cheap to rebuild is not one of them.

A tree-fitty on the other hand is dirt cheap.
 
Last edited:
I have a Mark's of Australia conversion on my '71 FJ40 that was upgraded at the time of the swap to a '79 4-speed and transfer case.

The Mark's kit is pretty straightforward. It's pluses are that it doesn't require much fiddling, it's complete, it's relatively simple, it properly indexes the motor out from the firewall, it uses existing components (factory tranny/transfer/bellhousing), and it works. It also keeps your FJ40 a bit more original, though that could be viewed as a moot point with a 350 under the hood.

It's minuses is that it costs more than other kits, you still don't get much of a low first gear, and no overdrive. (Of course, you could install an Aussie 5-speed, which has a lower first and overdrive, but that's adding another $1500 to $2500 depending on condition.)

I disagree that a 350 in and of itself is complex. It's not if you just run an HEI and carb it. That doesn't require much in the way of mods to the fuel system or electrical. Now if you go to electronic fuel injection, yeah, it can get complex.

Now, having said all that, would I do a Mark's kit if I was starting from scratch on my FJ40?

Only if I could get my hands on an Aussie 5-speed for a decent price.

I think I'd rather go with a 700R4 and mate it to the original transfer case, and use Advance Adaptors motor mounts (same as what's in the Mark's kit). Or possibly a manual tranny with a very low 1st and an overdrive. But the auto is a bit more attractive to me. I might go that route if something fails in the tranny or transfer requiring either to be pulled.

Cooling issues. This has been well discussed here, and a fan shroud on the stock radiator seems to work well for most people with a 350 conversion. That's a project for me for next spring. I've never overheated mine, though.
 
Good running 2F's are not hard to find and they are generally not that expensive. By not that expensive, I'm in the ball park of $500.00 for low milage one with 140+ psi per cylinder which includes everything from the air filter to the oil pan.

My 76 with 2F rolls on 35's with the 4:11's and 70mph on the freeway is not a problem. It's scary, but not a problem.
 
The Ranger is nice, I used to have one in my 66'. It doesn't require driveline mods or much hacking of the body(only the shifter through the floor). Nice thing is that it uses chevy manual bellhousing(not easy to find) and all chevy clutch parts so you don't have to mix and match like the other kits. It's awfully expensive and you'll have to decide if you want the overdrive or underdrive model.
Good luck
 
Go SBC and don't look back. Most of the other kits work, Mark's seems to be considered the best. The main point is take your time and do it right.
 
is there any welding required with Mark's adapter ?

End of hijack :D
 
is there any welding required with Mark's adapter ?

End of hijack :D

You'll have to weld in the front motor mounts.
I had a Mark's kit in my cruiser for a few years before I changed to an SM420. Never had any problems with it.
 
I am definately going with the Marks kit, now I just have to find who has the best price on it.

Final question. Is the GM power steering pump compatable with the Toyota mini truck power steering box that I have? I would rather not have to switch to a Saginaw steering box if I don't have to. I know custome lines will hvae to be made but I don't know if the pressure or flow from teh GM pump are to much for the mini truck box. Thanks to everyone for your help. This is a great site!!
 
I am definately going with the Marks kit, now I just have to find who has the best price on it.

Final question. Is the GM power steering pump compatable with the Toyota mini truck power steering box that I have? I would rather not have to switch to a Saginaw steering box if I don't have to. I know custome lines will hvae to be made but I don't know if the pressure or flow from teh GM pump are to much for the mini truck box. Thanks to everyone for your help. This is a great site!!

I run a GM pump and a mini box without any problems

Nocents
 
Back
Top Bottom