Is this causing my grrrs?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 3, 2017
Threads
33
Messages
931
Location
Arizona
Trail gear hub nuts. Since i tossed my front end together with new stuff ive had a high speed grrr, specifically on coast and highway turns at 65+.

Ive pulled my front driveshaft a few times and it gets quieter, but still there.

My wheel bearings were a little loose after mile 500, so I tightened them up. I checked them after 200 miles and seemed fine. Today at the 300 mile mark i have play (up down) again. No where near “bad” but not ideal either. 35” tire moves less than an 1/8” when pushed.

AC0C9BE9-F6B1-4951-9FB0-684DCC389FDF.webp


06C8579F-E3B9-4E2D-B346-871BA5FDA8E1.webp
 
Clearly been rubbing, but the cause??? Its greased in there, don’t see how it would make much noise.

44DDD96B-8293-4553-A0E0-BE83AE8DCD35.webp
 
Think thats a pretty common issue with those lock rings TG just doesnt seem to want to address. Most toss those screws and pick up a button head i believe thats a bit shallower. Quick search should yeild an answer.
 
Think thats a pretty common issue with those lock rings TG just doesnt seem to want to address. Most toss those screws and pick up a button head i believe thats a bit shallower. Quick search should yeild an answer.
I have seen that on threads, but would it cause noise? My drive flanges sealed 100% and didn’t have issues going on so I thought they addressed the issue. Guess not.

29302BA3-8F70-4382-87FC-894B9445BBC0.webp
 
your using the fancy flange i figured the bigger issue woudl be why your nuts or loose not the noise. figure that out first. the bolt should clearance itself and stop making noise. I don't think you'd hear much from that. probably not your noise issue but still address why their nuts are not working right.
 
Yes, that would make the GRRRR noise you're hearing.

What torque did you set your WB? Hopefully at 30-35 LB-FT. If lower or done with the fish scale, it's not enough.

I have followed the Tools R Us version and that is to set 25 to 35 LB-FT and have not had an issue with anything loosening up.

I also installed the TG nuts, but upon the advice of 'Mud collective, I installed the button-head screws right out of the gate and have not had an issue.

WB should NOT loosen in 500 miles. When I first rebuilt my front axle, I went OCD overboard to follow the FSM to a tee. Now, I've worked on other brands of 4x4 for lots of years, and I've always followed the GM version to torque to 45 LB, then back off and re-torque to 35. Then the lock-nut at 45. When I went back to that here, my problems went away.
 
your using the fancy flange i figured the bigger issue woudl be why your nuts or loose not the noise. figure that out first. the bolt should clearance itself and stop making noise. I don't think you'd hear much from that. probably not your noise issue but still address why their nuts are not working right.

Except that loose WB will allow less clearance due to the slight angle between the hub and spindle. WB MUST be tight first and foremost.
 
When i first did them i used the bass scale, but the last time i did the “guudenuff” and clearly it wasn’t. Got me some buttonheads.
 
I was planning on getting those but I think i'll keep the OEM. After all they have been used for over 40 years... Sometimes, simple is better...
 
Clearly been rubbing, but the cause??? Its greased in there, don’t see how it would make much noise.

View attachment 1798090
Check that the spindle bushing has ample lube before buttoning it back up. Dry bushing is common cause of grrrrrr, especially during coast.
 
Check that the spindle bushing has ample lube before buttoning it back up. Dry bushing is common cause of grrrrrr, especially during coast.
Will do. I ran out if time today, ill hit it on Saturday, actually tearing it all apart to make sure its all good, following fsm for everything
 
I could hear my TG supplied screws making contact with the hub. It sounded more like a squeaky brake pad.

Purchased panhead hex M3-0.5 x 10 for replacements.
 
So tell me again why you're using TG as opposed to OEM in this application.
Supposed to not back off, however, i think im going back to stock.

Not everything stock/factory is for the best, although it does with these for the most part.
 
I could hear my TG supplied screws making contact with the hub. It sounded more like a squeaky brake pad.

Purchased panhead hex M3-0.5 x 10 for replacements.
Hmmm. Any grease in there at the time? My real problem could be wheel bearing(new but I coulda f’ed that up too) or the brass bushing. It definitely gets louder as my truck loads to the side a lot, both sides, but louder on driver side.

I followed lcp’s advice on pulling drive flanges and front driveshaft, quiet as a church mouse. So not sure what that means.
 
So tell me again why you're using TG as opposed to OEM in this application.

I chose TG because my stock ones would keep backing off. I had bought new star washers and all from Cruiser Outfitters when I went through the front axle. I could not seem to hold tension on the RF spindle.

I have done lots of GM front axle and the thickness of the nuts are 2X what the Toyota ones are. Based on thread count, the Toyota ones scare me from a stripping the threads aspect.

So, I needed to change anyway, so I chose the TG due to more threads per nut. If I had my "perfect" application, I would do two of the TG nut with the star washer between, but there are not enough threads on the end of the spindle to allow that. I don't really care for the two tiny little screws that hold the keyed washer, as I feel they are inadequate.

The long and the short: If the TG fail for me, I will go back to the factory nuts (purchase new) and start over. Probably get a new spindle too (with bushing, not bearing).

I know the PO on mine hit a guardrail with the RF corner and jacked up a bunch of stuff. The shop that did the rebuild was sketchy and it's possible that the threads on the spindle have been stretched or damaged that I cannot see visually.
 
Still waiting on WabFab to ship me my TG hub nuts, been waiting over a year for them.

I did have some aftermarket OEM style hub nuts strip out on me a few years back so what is why I wanted to try the TG setup, with replacement screws...
 
Still waiting on WabFab to ship me my TG hub nuts, been waiting over a year for them.

I did have some aftermarket OEM style hub nuts strip out on me a few years back so what is why I wanted to try the TG setup, with replacement screws...
I could send you mine, lol
 
Back
Top Bottom