Is Slow Acceleration Normal?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 23, 2007
Threads
114
Messages
1,115
Location
Kennett Square, PA
Website
cruisin4parts.com
I feel like my Cruiser is not pulling hard enough, or maybe its just the way they are (all torque and not speed). I haven't owned it long enough to notice a change. I stop a stop sign and it takes like 5 seconds to get up to a good speed. Up a hill, forget it, you're doing 40 on the bottom of the hill and then doing a slow 30 mph at the top of a small hill (on the road). Something wrong or is it just the way it is?
I'd love to make it peppy and responsive on the road.
 
3FE? Fast?

:lol::lol:




Sorry, I couldn't resist...




Yes, that's totally normal for this motor. It is the way it is. It's "slow as cold tar moving uphill" (literally), but it's super-reliable, bulletproof, and will take you anywhere you want to go, on or off road. Just not very fast.

Peppy and responsive? Swap it out for a Chevy 350. That's pretty much the only way to go if you want to make it fast.


3FE specs:
- 155HP @ 4000 RPM
- 220 lb-ft @ 3000 RPM

I think those are the right RPMs, correct me if I'm wrong.
 
Last edited:
3-FE is slow even in the lighter FJ-62,
 
Alright, that's fine. I can live with the torque and not the speed! The 3FE is amazing though. Thanks!

hey, btw, I see you have roof lights, where did you put the wiring harness for the lights? I just put 4 KCs up on my rack.
 
Alright, that's fine. I can live with the torque and not the speed! The 3FE is amazing though. Thanks!

hey, btw, I see you have roof lights, where did you put the wiring harness for the lights? I just put 4 KCs up on my rack.

I've never been one to trust pre-assembled harnesses, so I built my own. Three wires per set of lights (2) going to the roof. I used 14AWG for the positive wires, 12AWG for the ground.

Me and a buddy ran one set down each raingutter, through the fenders, into the engine compartment, where they run to a sealed relay box. My side looks pretty shoddy compared to the side my buddy did... :o
 
Last edited:
Rain gutters, duh. I'll see if I can do it. Got a bunch of wire up there. Thank you!
 
Rain gutters, duh. I'll see if I can do it. Got a bunch of wire up there. Thank you!

I warn you though, it's a trick to get them to stay in. The raingutter will only hold two wires. I stuffed the positive wires into it, then bought a roll of two-sided tape stuff so I could stick on the ground wire.

I'll get a pic if you want. Of the side my buddy did, of course....
 
Last edited:
I got 8 wires going up there, it would be hard to get it in there and stay. I'll take a look at the picture maybe I can try that method.
 
Here ya go.

This is the set for the outer roof lights. You can see where and how the ground wire is secured to the gutter. The two positive wires are underneath it.
n539070227_1083062_6639.jpg



It's a bit hard to tell what you're looking at here, but this is where the harness runs into the engine compartment. The wires look like they are getting pinched, but rest assured, they aren't.
n539070227_1083061_6248.jpg
 
It may be true about the 3FE being slow, but mine runs stronger in the chasis it's in now. Don't ask me how. Maybe the timing jumped two degrees in the roll over. BTW, there's some that bump the timing from 7 degrees to 9 deg before TDC, if I'm not mistaken. They say it wakes the motor up nicely.
 
Wow!!! Let's see how i can make my truck look.....

......like crap!!! I know wires running everywhere... Just bite the bullet and remove the headliner and pillar plastic. Drill a hole in the roof and seal it up. How do ya think the heavy duty guys run clearance lights on their ford and chevy cabs. A little more time i know....but just trying to help bring the crap level down...;)
 
Ditto on the throttle cable tightening...but don't get it too tight or it will constantly be "stuck" in a higher RPM.

But yeah, the 3FE isn't a 1/4 mile race winning engine...but like others have said...keep it fed and watered and it will last you well beyond 300k miles with proper maint. and attention to detail. Mine's about to turn 200k miles, and it runs just fine...I'd trust it on a road trip without issue (I just won't get there first ;) ).
 
Ditto on the throttle cable tightening...but don't get it too tight or it will constantly be "stuck" in a higher RPM.

But yeah, the 3FE isn't a 1/4 mile race winning engine...but like others have said...keep it fed and watered and it will last you well beyond 300k miles with proper maint. and attention to detail. Mine's about to turn 200k miles, and it runs just fine...I'd trust it on a road trip without issue (I just won't get there first ;) ).

Haha, I remember when I first tightened my throttle cable... I went for a test drive and it wouldn't go lower than 2000 RPM :idea: :doh:


If you went on a road trip, you actually might get there first... Considering the others will have all broken down. ;p
 
......like crap!!! I know wires running everywhere... Just bite the bullet and remove the headliner and pillar plastic. Drill a hole in the roof and seal it up. How do ya think the heavy duty guys run clearance lights on their ford and chevy cabs. A little more time i know....but just trying to help bring the crap level down...;)

Meh. I like a little personality. :hillbilly: Besides, you don't even notice the wires unless you're looking for them.

Edit: BTW, heavy duty Ford/Chev/Dodge trucks come with built-in clearance lights.....
 
Back
Top Bottom