Idling and acceleration problems

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Two weeks since the Redline treatment and the problem came back....worse than ever.

Took the family down to the Living Desert in Palm Springs this weekend. After about 45 minutes of hwy driving, while going through town, the idle began going mad. It would not go below 1200 at a stop, requiring heavy brake pressure to keep it stopped, and when placed in N or P, would quickly rev to about 2200 rpm than drop back to 1000 than back up to 2200 than back down; up...down...up...down...etc.

After leaving the park and coming to the first stop sign the engine immediately stalled. After that, the engine idle continued to do the up...down thing described above.

I'm resigned to taking it to a shop as this problem seems beyond my 1-2:banana: capabilities. More diagnosis ideas would be appreciated.

Thanks
Perk
 
Perk,

It may help us if you will summarize what was done just prior to the problem and everything that you have done in attempting to correct the problem.

Robbie gave you several TPS & MAF pointers. Were you able to eliminate those as the cause?

The main wiring harness has 2 areas that have been known to cause problems. The first is where the harness is routed close to the EGR valve. The insulation on the wires can become brittle and crack from the heat. Strange problems will be a result and there are numerous symptoms including poor idling. The second area is where the harness goes into the firewall and underneath the glove box. This is where it goes in to the main ECU. Check it carefully.

-B-
 
Last edited:
I had a strange idle problem as well, turned out the wiring harness was compromised in both areas mentioned in the previous post. One other thing is to also check the throttle cable (thanks CDan). I did just a bit of basic testing by waiting until mine acted unusually and would press the throttle body end to be certain it was closing completely, it didn't change my trucks behavior. Could be a possibility since your's seems to change as you pull to a stop or change throttle position. I changed parts in the following order. #6 injector, TPS, fuel reg, and finally throttle cable, fuel filter wiring harness, and installed a cleaned set of injectors as the grand finale. Problem resolved after the final stage. Good Luck, certainly frustrating but with the help from this forum there will be a resolution.
 
A few questions.... Is an OBD II scan tool needed to test TPS and MAF? The wires in the wiring harness are encased so if the encasing is intact can the wires be damaged? If yes, how should one go about inspecting the wires? Should the throttle cable be tight(mine isn't)? Should the IAC valve be tested?

After looking through the FSM at the troubleshooting procedures, I think I'm ready to turn at least the diagnosis over to a professional. How long should it take a shop to run the inspections/tests discussed so far? It seems like for a professional mechanic with the proper tools it would just take a few minutes. Is it necessary to go to the dealer for these types of inspections, or should I just take the FSM to an indy(they would need it wouldn't they)? I would like to avoid my local Toyota dealer as they seem to exaggerate labor time.

Thanks,
Perk
 
Throttle cable should not be tight or close to it at idle. Dunno about other stuff. No check engine light? Does this light go on for a few seconds each time you start it (along with the ABS light, airbag light, etc)?

DougM
 
perk said:
The wires in the wiring harness are encased so if the encasing is intact can the wires be damaged? If yes, how should one go about inspecting the wires?

Yes, by the EGR valve. Unlikely under the glove box. Get yourself some high temp tape (heavy sliver stuff available at a speed shop) to reseal the harness after you open it. Some have been able to wiggle the harness in this location and change the problem (make it worse, cause it to start, make it stop, make it better...) I would think you could detect idle changes with some movement of that harness while the engine is running.

-B-
 
I was not able to get my to correct itself by just moving the wire, I could not understand why I could not. Not the most electrical saavy person around, so I can't explain why a new wiring harness fixed the problem when replaced, but couldn't get it into a position that it would solve the problem by moving it around. Maybe a slight loss of current in a very precise system made for some type of pulse or lack of signal.?.?. It was the most frustrating problem that I and several associates at the local Toyota dealer had ever experienced and I have been in the auto industry my entire life. Good luck, hopefully you will not have to replace as many parts as I did in the process. The wiring harness is a fairly serious undertaking, so I did not attempt it until I had ruled out EVERYTHING else, starting with the most obvious and the least expensive. Had to move most of the attempts from my repair file to my PM file as I continued to install with no change. Might want to do a search and reread the posts as well, I seemed to find something new with each reread. Mine was like solving a very complex (expensive) problem and it only had a ~25 rpm drop, driveable but very annoying each time you stopped and would let the truck idle.
 
I took it to a shop here in Redlands to test TPS, MAF, IAC, and run a complete computer diagnostic. Everything was within parameters except..................... TPS was improperly set at 9 degrees. He set it back to 5.5-6 degrees and its now idling at 650 rpm and acceleration and shifting are more responsive and engine feels smoother. I haven't gone on an extended drive yet, but hopefully problem solved.

Good call Beo, CJF, and of course Robbie, you guys had TPS in mind all along.

Thanks to all who lent their expertise,
Ted
 
Ugly head reared again....over the last two weeks, a low idle (3-400rpm) has occurred a few times. Unlike before, it is not stalling or even running rough once dropped down, likely the result of the TB cleaning and TPS adjustment. Each time, if I turn the engine off and restart, the idle goes back to normal.

When I discussed this with the owner of the shop who did the TPS adjustment, he said that the computer didn't show anything out of perameter and that they did physically check the resistances on the MAF, IAC, and TPS. He also said that even though the MAF, IAC, TPS all tested OK, there still could be a problem with one of these because they will test/behave differently under different driving conditions.

Today, while on the freeway, I turned on the AC, for the first time in many months. When I got to the end of the offramp, it was doing the same high idle business as before where it's at about 1200 rpm, wanting to pull away and when placed in P or N the engine starts revving to about 2200 than falling back down to 1200 over and over. I turned the engine off, restarted and back to normal.

Given these new data points, where's the next best place to look? Could O2 sensors have anything to do with this, just turned 100K on the clock and they're original?


Thanks,
Perk
 
It not the O2 sensors.

While neither is good, the surging idle would concern me more than the low one for now; I'd go after that first.

Off the top of my head, the only things I can think of that can do what you're describing are sticking linkages or (again...) the TPS.

Anyone else??

Curtis
 
Thanks CJF,

Could there be something wrong with the TPS even though it's in the proper position and the resistances were all ok? How does the TPS work, sure seems like an odd little item.

Does anyone else have any ideas about this?


Many thanks in advance,
Perk
 
By "proper position", you mean the ohmmeter deflection test with a feeler gauge at the back of the throttle body? If you've done that and the other resistance tests, then I'm afraid I'm out of good ideas. :frown:

Now bad ideas, on the other hand, I've got plenty of. :D One would be to rotate the TPS to increase the deflection distance a little bit anyway, just to see if it changes anything. I actually think I'd try that if I were in your shoes, since too small a gap could definitely be causing the high idle. (Which again more immediately concerns me than the low idle.)

Keep in mind this whole (TPS) direction of inquiry might be a dead end. I just got nothin' else.

I feel for ya, man; hang in there.

Curtis
 
Re-reading this thread, I think my "bad idea" in the above post is probably just beating a dead horse.

This is really bugging me though: I simply cannot imagine what would allow the motor to cycle from 1200-2200 (:eek:!) rpms in park without your foot on the gas!
 
Would you need to reset the ecu by pulling the fuse after each corrective step? It probably doesn't make that big of a difference, I just did it during my search to be thorough.
 
The underhood fuse box contains the fuse, I just pulled for ~60 seconds, replaced and then allowed to idle for several minutes to relearn any programming. Definitely will not FIX anything just allow any fixes to better match up to the ecu program.
 
another data point, since mine was acting a little weird (97 lx450) after a HG job:

mine was iding a little rough and higher than normal: obd2 laptop software showed 12% throttle at idle. I didn't have an FSM, but based on your previous post i turned it down to 6%. it was great for a couple of days, but now it's dropping a little under 600 RPM at idle, so i ponied up $10 for the online FSM. that says;: "7-11% at idle" at least for a 97.

I'm going to follow the TPS adjustment procedure per the manual with an ohmmeter to see if it helps.

And the a/c compressor does tend to shoot the RPMs up quite a ways on mine...not sure it goes to 2200, but i'll watch it more closely and post what it does.
 
Back
Top Bottom