Hub diff fluid leak

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 1, 2017
Threads
3
Messages
19
Location
New Braunfels, TX
Howdy Folks,
Finally got my cruiser and it's been a blast. On recent road trip I noticed fluid being spun out on wheel. Just want to double check my plan. Replace seals and bearings and inner axle seal?

Looking forward to many days of dusty trails.
97' FJZ 233'000 miles, disc brakes

Thanx Brad

20170604_181157.webp
 
Front or rear?

If front, it's time to go through the whole front end, ie "knuckle rebuild". This is usually a good idea on a new to you truck anyway.

If rear, easy job.

The wheel bearings may be good. Check them before replacement.
 
Forgot to mention rear. Is there suppose to be a seal to keep diff fluid out of hub? I'm getting service manual this afternoon.
 
Since it's on the OUTSIDE, it appears to be an axle flange seal.

Pull the axle, clean the faces, use some "The Right Stuff" gasket sealer and bolt it back on.

The rear wheel bearings are lubed by the diff oil (or at least can be). There IS an inner axle seal that goes just inside the spindle, but it's "weak" and is supposed to help keep the diff oil out of the wheel bearings so you can run WB grease. Both ways will work. You can install a new inner axle seal AND the paper gasket on the axle flange or use The Right Stuff to get that part sealed.

Check your wheel bearing play while you have the axle out. If none, let it be.
 
So just so you know, that's not the best advice from Bilt4me.

There is an inner axle seal in the spindle that does an excellent job keeping the gear oil out of the hub When it gets in the hub, it washes out the grease. American axle hubs like 14 bolts and D60s are built to run in oil, the Toyota axle is not, and will make a mess like you already have.

There is nothing "weak" about the inner axle seal. It's lasts for a long time, but over time it dries out and then no longer seals. Not surprising in a 20 year old truck with >200k miles.

Recommend you get the inner seals and the outer paper gasket and repair it properly. It's very easy in the rear.

Cruiseroutfitters @cruiseroutfit sells a rear axle rebuild kit with bearings that I thought was good and fairly priced, but will also have just the seals and gaskets if you go that route. One hint-the little screws that lock the thrust washer are soft and easy to strip. I'd recommend you pop them loose with an impact driver which does a good job without damaging them.
 
I'm firmly in the camp that the rear inner axle seals suck, don't recall ever taking one apart that didn't have oil in the bearings. With the seal in there, the gear oil doesn't circulate, is more trapped in the hub, so tends to run higher than ideal, more likely to leak. Without the seal, oil is free to be replenished from the diff, runs at a more ideal level.

Have done them both ways, now, unless the owner insists, we leave the seal out, have done a bunch this way with zero issue. Oil is a better lube than grease, and it reduces maintenance to an occasional play/preload check. In the end, doesn't matter, likely to be running on oil sooner than later!:hillbilly:
 
... On recent road trip I noticed fluid being spun out on wheel. ...

The first thing to check is the studs, why was it leaking at the axle? Most often it's from the nuts being loose, if so the studs should be replaced. They are highly stressed, torque close to yield, if they have come loose, are likely compromised, may not hold rated tension causing a repeat of this problem or worse. Would get the correct studs, they are unique to the application, but are relatively common, Cruiser Outfitters or dealer, etc.
 
From: Cruiser Outfitters

Aisin Hub/Drive Flange Stud - $1.75
Six required per side, 12 per axle
(Fits 1958-1/1998 40/55/6062/70/80 Series)
Part# HUB08235
 
Awesome advice all around!
Cleaned up the wheel, bolts did need to be torqued down. Refilled fluid will drive to check for effect. If still leaking will replace all the seals, gasket, bearings etc.

Very interested in the pros and cons of replacing inner oil seal?
 
Awesome advice all around!
Cleaned up the wheel, bolts did need to be torqued down. Refilled fluid will drive to check for effect. If still leaking will replace all the seals, gasket, bearings etc.

Very interested in the pros and cons of replacing inner oil seal?


I'd say post #5 and #6 pretty much sum it up.

One says Toyota designed to run with grease only.
Dana 60's, 70's, and GM Corporates are designed to run in diff oil.

The Toyota seal fails and then it's running in oil......Will it blow up? No. Will it leak? Maybe .........

When I installed new inner spindle (axle) seals for the rear, I thought I was missing something, as they are almost like a square O-Ring that slips into the spindle. It doesn't feel as though they would do much or that they may fail early.

I made sure that the grease I used on the bearings on the rear axle was compatible with the oil I used in the differential, because EVENTUALLY, they will mix at the hub. Some synthetics don;t play well with non-synthetics and they clump.

I used Lucas Red-N-Tacky 2 for the wheel bearings and regular 80W-90 for the diff oil (Dino) O'Reilly House brand. I buy it in the 5-gallon bucket......
 
Well, finally found time to take care of hub. Or at least I thought. After securing 2 bolt to pull axle off hub, one bolt sheared off! Great, after getting that bolt drilled out and removed, I could not get the axle free of the hub. Finally ran out of time. Will make another go at it after I get some hardened screws to pull axle off.
Any tips for freeing the axle from rear hub. One thing I didn't think of till afterwards was grabbing it with large channel lock and giving it a wiggle.

Thanks
 
Did you loosen/remove the cone washers (not the nuts, I assume you did those) first?
 
Did you loosen/remove the cone washers (not the nuts, I assume you did those) first?
Yes sir,
Could not get cone washers to loosen, removed the nuts, tapped with brass bar, tapped a little harder with brass bar, attempted to loosen by grabbing with vice grips. Nothing!
 
It might surprise you how hard you have to hit those studs to get the cone washers out.

If nothing else works use a small sharp punch in the gap of the cone washer. You'll need to replace them after that though.

Either way if they aren't out the threaded holes won't work.

IIRC the FSM says to hit the center of the rear hub flange to loosen them but I could never get that to work.. even hitting it REALLY hard.
 
It might surprise you how hard you have to hit those studs to get the cone washers out.

If nothing else works use a small sharp punch in the gap of the cone washer. You'll need to replace them after that though.

Either way if they aren't out the threaded holes won't work.

IIRC the FSM says to hit the center of the rear hub flange to loosen them but I could never get that to work.. even hitting it REALLY hard.
I just picked up 12 cone washers, nuts, lock washers, studs, and gaskets. Wanted to have everything on hand for my next attempt.
 
Also check your diff bteather to make sure it's operating and venting pressure.

I did a 4 mile drive a few days ago and pulled the 80 into the driveway to install a tailgate storage lid. I found fresh diff oil running down the inside of the ps back tire. I really hope it is my diff breather. I haven't messed with it for ten years. I already need to deal with a leaky PS pump, front pinion seal and a front axle service. I could stand a little good luck in the leak department.
 
I did a 4 mile drive a few days ago and pulled the 80 into the driveway to install a tailgate storage lid. I found fresh diff oil running down the inside of the ps back tire. I really hope it is my diff breather. I haven't messed with it for ten years. I already need to deal with a leaky PS pump, front pinion seal and a front axle service. I could stand a little good luck in the leak department.
I plan on checking the breather also, other wise I'm surprised to be leak free on 20yo vehicle.
 
I did a 4 mile drive a few days ago and pulled the 80 into the driveway to install a tailgate storage lid. I found fresh diff oil running down the inside of the ps back tire. I really hope it is my diff breather. I haven't messed with it for ten years. I already need to deal with a leaky PS pump, front pinion seal and a front axle service. I could stand a little good luck in the leak department.

Could also just be loose bearings allowing the hub to move around and fluid to get past the seal.
 
Could also just be loose bearings allowing the hub to move around and fluid to get past the seal.

Na-na-na-an, I can't hear you. Repeat after me, "it was hot, your breather is clogged, you just sent a little oil past the seal" :lol:

The wheel doesn't feel loose, but I do have a full rebuild kit that has been sitting in the parts drawer for seven years.
 
Back
Top Bottom